454 4 bolt main bare block - The 1947 - Present Chevrolet & GMC Truck Message Board Network

tmcgrawlookalike · 09-10-2005, 08:26 AM

fresh from machine shop.needs final hone for sizing of pistons `you` decide to use.fresh .060 bore.comes with cam bearings/freeze plugs installed.this is a low deck,passenger car/light truck/motorhome block,NOT a high deck,2 ton truck,bus block,which are getting hard to find.e-mail only please at tmcgrawlookalike@hotmail.com.buyers responsibility for pick-up/shipping.i should be able to crate and deliver to shipping dock for you as long as you take care of any/all charges.in oklahoma city,oklahoma.550.00 FIRM-I ALSO HAVE A SRP PISTON/EAGLE CRANK/EAGLE I-BEAM OR H-BEAM KIT TO GO WITH THIS AT A HELL OF A PRICE.ASK ABOUT IT!!MARK

Mad Dog · 09-10-2005, 09:08 AM

How much for the rotating assembly?

tmcgrawlookalike · 09-11-2005, 11:30 AM

well,lets see.i have a kit with 12.8/1(119cc o/c head)srp pistons(.060) or a kit with 10.3/1 srp pistons(.060)(119 o/c head),choice is yours.either kit with eagle i-beam rods,forged 4340 crank,h-series clevite bearings,file-fit sealed power plasma moly rings,sell at 1500.00.if you want the h-beam rods,and 100.00.you must final balance this assembly with your flywheel,balancer,etc.you will also be responsible for shipping.i also have 049,781,840,cast,aluminum,oval,rectangular,valve covers,gear drives.other than heads,this stuff is all new.

tmcgrawlookalike · 09-11-2005, 04:02 PM

anyone?

acloco · 09-11-2005, 04:26 PM

How can you finish hone a block when the cam bearings and soft plugs are installed already?

Sorry....I have seen people try to do this before...and end up eating an engine.

tmcgrawlookalike · 09-11-2005, 11:16 PM

cam bearings NOT installed,but come with it.freeze plugs installed,but will not affect ANYTHING as far as final hone is concerned.sorry acloco,i did not specify but didn`t think i`d have to either.

acloco · 09-11-2005, 11:18 PM

Cool....I worked in a machine shop....the horror stories are like an emergency room.

Larry68GMC · 09-12-2005, 02:36 AM

You got mail....

tmcgrawlookalike · 09-13-2005, 08:15 PM

anyone?

09-10-2005, 08:26 AM	#1
tmcgrawlookalike Registered User Join Date: Jun 2004 Location: warr acres,oklahoma Posts: 650	454 4 bolt main bare block fresh from machine shop.needs final hone for sizing of pistons `you` decide to use.fresh .060 bore.comes with cam bearings/freeze plugs installed.this is a low deck,passenger car/light truck/motorhome block,NOT a high deck,2 ton truck,bus block,which are getting hard to find.e-mail only please at tmcgrawlookalike@hotmail.com.buyers responsibility for pick-up/shipping.i should be able to crate and deliver to shipping dock for you as long as you take care of any/all charges.in oklahoma city,oklahoma.550.00 FIRM-I ALSO HAVE A SRP PISTON/EAGLE CRANK/EAGLE I-BEAM OR H-BEAM KIT TO GO WITH THIS AT A HELL OF A PRICE.ASK ABOUT IT!!MARK

09-10-2005, 09:08 AM	#2
Mad Dog Registered User Join Date: Jun 2005 Location: Independence MO Posts: 87	How much for the rotating assembly? __________________ 72 C10 longbed 5/7 drop, Telstars, 350/th400(for now) 69 Chevelle SS396 (427/th400) 88 K5 on 35's (355/700R4/208)

09-11-2005, 11:30 AM	#3
tmcgrawlookalike Registered User Join Date: Jun 2004 Location: warr acres,oklahoma Posts: 650	well,lets see.i have a kit with 12.8/1(119cc o/c head)srp pistons(.060) or a kit with 10.3/1 srp pistons(.060)(119 o/c head),choice is yours.either kit with eagle i-beam rods,forged 4340 crank,h-series clevite bearings,file-fit sealed power plasma moly rings,sell at 1500.00.if you want the h-beam rods,and 100.00.you must final balance this assembly with your flywheel,balancer,etc.you will also be responsible for shipping.i also have 049,781,840,cast,aluminum,oval,rectangular,valve covers,gear drives.other than heads,this stuff is all new. Attached Images

09-12-2005, 02:36 AM	#8
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	You got mail.... __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

09-11-2005, 04:02 PM	#4
tmcgrawlookalike Registered User Join Date: Jun 2004 Location: warr acres,oklahoma Posts: 650	anyone?

09-11-2005, 04:26 PM	#5
acloco Registered User Join Date: Apr 2004 Location: Nebraska Posts: 335	How can you finish hone a block when the cam bearings and soft plugs are installed already? Sorry....I have seen people try to do this before...and end up eating an engine.

09-11-2005, 11:16 PM	#6
tmcgrawlookalike Registered User Join Date: Jun 2004 Location: warr acres,oklahoma Posts: 650	cam bearings NOT installed,but come with it.freeze plugs installed,but will not affect ANYTHING as far as final hone is concerned.sorry acloco,i did not specify but didn`t think i`d have to either.

09-11-2005, 11:18 PM	#7
acloco Registered User Join Date: Apr 2004 Location: Nebraska Posts: 335	Cool....I worked in a machine shop....the horror stories are like an emergency room.

09-13-2005, 08:15 PM	#9
tmcgrawlookalike Registered User Join Date: Jun 2004 Location: warr acres,oklahoma Posts: 650	anyone?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.