electric fan strength - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Nickbo · 04-14-2002, 01:14 PM

will an electric fan keep my 350 cool enough, should I pull air or push it

Nickbo · 04-14-2002, 03:44 PM

ttt.... engine makes near 400 horse, help.

Nickbo · 04-14-2002, 04:01 PM

ttt

Nickbo · 04-14-2002, 04:25 PM

ttt

**Tim Christian** · 04-14-2002, 08:08 PM

I know Wes is running one on his big block and he says it does just fine but I don't know if it pushes or pulls

------------------
67 GMC Stepside(UNDER CONSTRUCTION)
67 GMC Custom
67 Chevy C-30

Longhorn Man · 04-14-2002, 08:09 PM

His is a puller...it is inside the engine compartment.

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio

Low69CST · 04-14-2002, 09:05 PM

i've always heard pullers are better than pushers

------------------
'69 CST Short fleetside
Lowered, 400 small block, 700R4, 3" dual exhaust, 40 series Flowmasters, 4 wheel disc brakes, all stainless hard and flex lines, front & rear sway bars, Dana 9 1/4" rear end 4.11's w/Detroit Locker, soon to have 18" rims
Not my daily driver. More like my weekend A$$ KICKER.
See my truck at: http://www.geocities.com/low69cst/
Future Automotive Engineer attending the University of Kentucky.
Feel free to message me on AOL, SN- SS95ZQ8
My Dad's projects:
72 Short Fleet 4x4 Chyenne Super
72 Long Fleet 4x4 Chyenne Super
Both 350 autos restored original

Nickbo · 04-14-2002, 11:50 PM

The fans I been looking at are good for up to 260 horse, I have a lot more than that, just wondering if there is a strong enough fan to do the job.

Low68 · 04-15-2002, 12:54 AM

Check out this website: http://www.rbsauto.com/Top%20100/Cat...ted/EN_01.html .
I have heard that Spal makes good products. Good luck

------------------
http://www.geocities.com/a68rod

bigvinnie · 04-15-2002, 02:56 AM

I installed a flexalite fan that I ordered from summit.... it's a 16 inch unit, pulls 2800 cfm, with its own shroud and mounting hardware. I mounted it in the original fan shroud and I've had good results.

I was having cooling problems after putting an A/C condensor and trans cooler in front of my 4 row radiator... I haven't had a problem since.

------------------
'72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA
http://www.ixpres.com/vlusardi/chevtrk.htm

Nickbo · 04-15-2002, 08:46 AM

thanks everyone.

04-14-2002, 01:14 PM	#1
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	electric fan strength will an electric fan keep my 350 cool enough, should I pull air or push it __________________ 1967 was a good year

04-14-2002, 03:44 PM	#2
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	ttt.... engine makes near 400 horse, help. __________________ 1967 was a good year

04-14-2002, 04:01 PM	#3
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	ttt __________________ 1967 was a good year

04-14-2002, 04:25 PM	#4
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	ttt __________________ 1967 was a good year

04-14-2002, 09:05 PM	#7
Low69CST Registered User Join Date: May 2000 Location: Frankfort, Kentucky, USA Posts: 2,163	i've always heard pullers are better than pushers ------------------ '69 CST Short fleetside Lowered, 400 small block, 700R4, 3" dual exhaust, 40 series Flowmasters, 4 wheel disc brakes, all stainless hard and flex lines, front & rear sway bars, Dana 9 1/4" rear end 4.11's w/Detroit Locker, soon to have 18" rims Not my daily driver. More like my weekend A$$ KICKER. See my truck at: http://www.geocities.com/low69cst/ Future Automotive Engineer attending the University of Kentucky. Feel free to message me on AOL, SN- SS95ZQ8 My Dad's projects: 72 Short Fleet 4x4 Chyenne Super 72 Long Fleet 4x4 Chyenne Super Both 350 autos restored original __________________ '69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks

04-14-2002, 08:08 PM	#5
Tim Christian Senior Member Join Date: Dec 1999 Location: TN/VA Posts: 6,388	I know Wes is running one on his big block and he says it does just fine but I don't know if it pushes or pulls ------------------ 67 GMC Stepside(UNDER CONSTRUCTION) 67 GMC Custom 67 Chevy C-30

04-14-2002, 08:09 PM	#6
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	His is a puller...it is inside the engine compartment. ------------------ '69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it. FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite. If you need a pic posted, E-mail me at longhornmail@yahoo.com Andy, in Columbus Ohio

04-14-2002, 11:50 PM	#8
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	The fans I been looking at are good for up to 260 horse, I have a lot more than that, just wondering if there is a strong enough fan to do the job. __________________ 1967 was a good year

04-15-2002, 12:54 AM	#9
Low68 Registered User Join Date: May 2001 Location: Arizona Posts: 758	Check out this website: http://www.rbsauto.com/Top%20100/Cat...ted/EN_01.html . I have heard that Spal makes good products. Good luck ------------------ http://www.geocities.com/a68rod __________________ Build Thread

04-15-2002, 02:56 AM	#10
bigvinnie Registered User Join Date: Aug 2001 Location: escondido, ca 92026 Posts: 1,222	I installed a flexalite fan that I ordered from summit.... it's a 16 inch unit, pulls 2800 cfm, with its own shroud and mounting hardware. I mounted it in the original fan shroud and I've had good results. I was having cooling problems after putting an A/C condensor and trans cooler in front of my 4 row radiator... I haven't had a problem since. ------------------ '72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA http://www.ixpres.com/vlusardi/chevtrk.htm __________________ '72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project

04-15-2002, 08:46 AM	#11
Nickbo Registered User Join Date: Feb 2000 Location: colorado springs, colorado, usa Posts: 289	thanks everyone. __________________ 1967 was a good year



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.