What do I have here? (Posi) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

HuggerCST · 08-09-2006, 03:24 PM

It looks similar to a 12 bolt truck posi, but is a couple of inches wider, and has a few other small differences. Can anyone identify it?

see ten · 08-09-2006, 04:36 PM

I'm not real familiar with them but isn't that called a Gov-lock?

LUV2XCLR8 · 08-09-2006, 04:41 PM

Me either, but I think Asa is close

onetonk5 · 08-09-2006, 04:47 PM

I dont see the deal on the outside of the case that swings out to lock...or split the carrier in half.....that looks a lot like the clutch type posi in my 12 bolt.

larry may · 08-09-2006, 05:21 PM

Might be off a bit here . However; Looks similar to the M-1009 Blazer the military use. Thinking they were Dana 44 in the rear. My .02%

onetonk5 · 08-09-2006, 05:50 PM

im pretty sure chevy has never built a production truck with a 44 rear

HuggerCST · 08-10-2006, 10:26 PM

I don't think it's a gov lock. Could be the Dana I guess. ??? Here is a pic of it on the right compared to a 12 bolt '72 chevy 1/2 ton 4:11 posi on the left.

onetonk5 · 08-10-2006, 11:35 PM

Whats the spline count?Might help narrow it down.

BobbyK · 08-11-2006, 12:20 AM

This is a 12 bolt Gov-Loc.

And the other side.

HuggerCST · 11-28-2009, 08:22 PM

Ok this thing is still sitting around my shop and I still don't know what it fits. It is for 30 spline axles. I was told that it is from a chevy truck, but must be 3/4 ton? Any ideas?

Willys47 · 11-28-2009, 09:44 PM

maybe it's for a dana 60

292farmer · 11-28-2009, 10:49 PM

i saw an ED maybe its an Eaton Differential setup, like in some of the military cucv's? and in some 12 and 14 bolts?

Bob 68327 · 11-28-2009, 10:55 PM

Quote:

Originally Posted by onetonk5

im pretty sure chevy has never built a production truck with a 44 rear

There were quite a few leaf spring 1/2 ton 2wd with dana 44's in them . I have a 67 gmc rear in my 68 and it is a dana 44. I don't know if that is what the center section fits cause I have never opened mine up . If it is I would be very interested.

vectorit · 11-28-2009, 11:04 PM

I think it looks like an Eaton unit with that thick ring gear back plate, but the single spring makes me not sure.

Davetopay · 11-28-2009, 11:24 PM

Quote:

Originally Posted by onetonk5

im pretty sure chevy has never built a production truck with a 44 rear

NOt an expert by ANY means, but I know in resto parts catalog, they list rearend rebuild kits for D44 axles.

QKENUF4U · 11-29-2009, 12:26 AM

here ya go.....

http://www.chevy-camaro.com/parts/ch...codes-diff.htm

The 12 bolt eaton 2 series posi has the casting number
2 series, ED-32088
3 series, EDB-30140
4 series, EDB-30174

66skylarkpost · 11-29-2009, 12:36 AM

nevermind

08-09-2006, 03:24 PM	#1
HuggerCST Registered User Join Date: Jul 2001 Location: North Louisiana Posts: 4,501	What do I have here? (Posi) It looks similar to a 12 bolt truck posi, but is a couple of inches wider, and has a few other small differences. Can anyone identify it? Attached Images __________________ Wynne 70 CST short fleet Hugger orange & white, 350/350, ps, pb, air, tilt, tach/vac/speedwarning, original buckets, AM/FM, oak bed floor, shoulder belts, 3.5"/5.5" drop, 20" American Racing VN425s. Build thread 53 Chevy shortbed 69 Camaro Click here to subscribe Chevy GMC International Truck Club Louisiana Charter Member http://www.louisianaclassictruckclub.com

08-09-2006, 04:36 PM	#2
see ten WTB this ad Join Date: Sep 2004 Location: Lafayette Georgia Posts: 5,074	Re: What do I have here? (Posi) I'm not real familiar with them but isn't that called a Gov-lock?

08-09-2006, 04:41 PM	#3
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: What do I have here? (Posi) Me either, but I think Asa is close __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

08-09-2006, 04:47 PM	#4
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: What do I have here? (Posi) I dont see the deal on the outside of the case that swings out to lock...or split the carrier in half.....that looks a lot like the clutch type posi in my 12 bolt. Last edited by onetonk5; 08-09-2006 at 04:47 PM.

08-09-2006, 05:21 PM	#5
larry may Senior Member Join Date: Jul 2005 Location: MISSOURI Posts: 3,256	Re: What do I have here? (Posi) Might be off a bit here . However; Looks similar to the M-1009 Blazer the military use. Thinking they were Dana 44 in the rear. My .02%

08-09-2006, 05:50 PM	#6
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: What do I have here? (Posi) im pretty sure chevy has never built a production truck with a 44 rear

08-10-2006, 10:26 PM	#7
HuggerCST Registered User Join Date: Jul 2001 Location: North Louisiana Posts: 4,501	Re: What do I have here? (Posi) I don't think it's a gov lock. Could be the Dana I guess. ??? Here is a pic of it on the right compared to a 12 bolt '72 chevy 1/2 ton 4:11 posi on the left. Attached Images __________________ Wynne 70 CST short fleet Hugger orange & white, 350/350, ps, pb, air, tilt, tach/vac/speedwarning, original buckets, AM/FM, oak bed floor, shoulder belts, 3.5"/5.5" drop, 20" American Racing VN425s. Build thread 53 Chevy shortbed 69 Camaro Click here to subscribe Chevy GMC International Truck Club Louisiana Charter Member http://www.louisianaclassictruckclub.com

08-10-2006, 11:35 PM	#8
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: What do I have here? (Posi) Whats the spline count?Might help narrow it down.

08-11-2006, 12:20 AM	#9
BobbyK Registered User Join Date: May 2000 Location: Petrolia,Ontario,Canada but working in Port Huron,Mi. Posts: 1,772	Re: What do I have here? (Posi) This is a 12 bolt Gov-Loc. And the other side. __________________ 71 blazer,350SBC,approx.375HP,700R4,factory GM TPI.Dual electric fans,33x12.5x15 ATR on stock suspension. Petrolia,Ontario,Canada but working in Port Huron,MI. See ALL my Blazer pic's HERE

11-28-2009, 08:22 PM	#10
HuggerCST Registered User Join Date: Jul 2001 Location: North Louisiana Posts: 4,501	Re: What do I have here? (Posi) Ok this thing is still sitting around my shop and I still don't know what it fits. It is for 30 spline axles. I was told that it is from a chevy truck, but must be 3/4 ton? Any ideas? __________________ Wynne 70 CST short fleet Hugger orange & white, 350/350, ps, pb, air, tilt, tach/vac/speedwarning, original buckets, AM/FM, oak bed floor, shoulder belts, 3.5"/5.5" drop, 20" American Racing VN425s. Build thread 53 Chevy shortbed 69 Camaro Click here to subscribe Chevy GMC International Truck Club Louisiana Charter Member http://www.louisianaclassictruckclub.com

11-28-2009, 09:44 PM	#11
Willys47 Registered User Join Date: Dec 2007 Location: Nanaimo B.C. Posts: 604	Re: What do I have here? (Posi) maybe it's for a dana 60 __________________ I was hooked on these trucks since 1982 when I drove my budys fathers 1968 Custum GMC 396 automatic dana 60 rear with a power lock diff what a ride more fun then we will we can ever tell!!

11-28-2009, 10:49 PM	#12
292farmer Registered User Join Date: Nov 2009 Location: stoddard nh Posts: 693	Re: What do I have here? (Posi) i saw an ED maybe its an Eaton Differential setup, like in some of the military cucv's? and in some 12 and 14 bolts? Last edited by 292farmer; 11-28-2009 at 10:50 PM.

11-28-2009, 11:04 PM	#14
vectorit What? Join Date: Jun 2007 Location: Southern California Posts: 7,617	Re: What do I have here? (Posi) I think it looks like an Eaton unit with that thick ring gear back plate, but the single spring makes me not sure. __________________ Chris 1968 K20 Suburban 1972 K10 LWB PU

11-29-2009, 12:26 AM	#16
QKENUF4U Senior Member Join Date: Jan 2005 Location: SUNNY WARM BIKE RIDING COTTONWOOD ARIZONA Posts: 2,097	Re: What do I have here? (Posi) here ya go..... http://www.chevy-camaro.com/parts/ch...codes-diff.htm The 12 bolt eaton 2 series posi has the casting number 2 series, ED-32088 3 series, EDB-30140 4 series, EDB-30174 Last edited by QKENUF4U; 11-29-2009 at 12:27 AM.

11-29-2009, 12:36 AM	#17
66skylarkpost Registered User Join Date: Mar 2006 Location: kearney,nebraska Posts: 443	Re: What do I have here? (Posi) nevermind Last edited by 66skylarkpost; 11-29-2009 at 12:40 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.