|
04-23-2002, 09:32 AM
|
#1 |
|
Registered User
Join Date: May 2000
Location: Rohnert Park, CA
Posts: 615
|
Starter/Shim ??
The Starter on my Burb started acting up, it would click when i turn the key almost like bad contact so i swapped for another i had that i thought was good, it did the same thing. If i tap on solonoid i here it retracting like it was stuck then it will start! I don't think both starters are bad (solonoid) I have heard of shimming the starter could this keep the soloniod from hanging up and where do i get these shims?
------------------ 72 GMC Burb barn door 4X4 350/350 PS PB Tilt 62 Chevy Nova Convertible 64 Chevy II V8 Loaded Wagon VW Offroad buggy 84 700SC Honda Nighthawk
__________________
72 GMC Burb barn door 4X4 350/350 PS PB Tilt ( gone but not forgooten) 64 Chevy II V8 Loaded Wagon 2004 Chevy 2500 HD Sonoma County, Northern CA |
|
|
|
04-23-2002, 11:32 AM
|
#2 |
|
Recovering Truck Driver
Join Date: Mar 2002
Location: Orleans, NE USA
Posts: 1,883
|
Chances are the shims won't do any good for the solenoid, if it's not trying to crank. The are there to adjust tooth contact with the flexplate. It could be a bad ground with the block. If you need shims, they are available from any parts store, and sometimes in a variety pack. Also, some junkyards keep a box of them around.
------------------ Ol' Buck: '72 Chevy 1/2T 4x4 shortbox stepside 350/350auto on '84 ralleys and 31/10.5s Angel girl: 67 Cutlass convertible 330, 3spd stick Greener: 90 GMC Jimmy 350/auto Chad Stephens Orleans,NE no name yet: 72 442 under serious construction
__________________
67 K-20 350, SM465, Eaton rear, 4.56 no spin option 00 Dodge 2500 4x4, 24V cummins, 5 speed Chad South Central Nebraska |
|
|
|
|
04-23-2002, 12:47 PM
|
#3 |
|
Registered User
Join Date: May 2001
Location: Honolulu, HI
Posts: 1,237
|
I shimmed my starter 5 years ago with a piece of a crushed beer can. Stomped the can, cut out a little "C" and put it up around a bolt. Worked like a charm.
|
|
|
|
|
04-23-2002, 02:35 PM
|
#4 |
|
Registered User
Join Date: May 2000
Location: Rohnert Park, CA
Posts: 615
|
O'l Buck The Solonoid pushes the small gear out to contact the flex plate, but what seems like is happening is its not contacting properly and getting stuck out! If i tap with a hammer it releases and i can start or it will jam again. I think the ground is good as well as the battery posts and cables clean.
------------------ 72 GMC Burb barn door 4X4 350/350 PS PB Tilt 62 Chevy Nova Convertible 64 Chevy II V8 Loaded Wagon VW Offroad buggy 84 700SC Honda Nighthawk
__________________
72 GMC Burb barn door 4X4 350/350 PS PB Tilt ( gone but not forgooten) 64 Chevy II V8 Loaded Wagon 2004 Chevy 2500 HD Sonoma County, Northern CA |
|
|
|
|
04-23-2002, 06:44 PM
|
#5 |
|
Registered User
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
|
it might be too tight dude. A fast tip on starters.......slide a 1/8" rod between the armature shaft & the OD of the flex plate.....not loose,but not tight,& you are shimmed properly.....69
__________________
http://community.webshots.com/user/hotrodhorn |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
