new engine in K5 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

WORNBRAKES · 01-09-2008, 06:37 PM

I have it installed and running. Still have some tunning to do with dizy and carb but I am happy with the upgrade so far. Aint she perty?

BLUE THUNDER · 01-09-2008, 07:08 PM

Congrats on the motor. I'm doing the same thing. Putting in a 305 while the 350 gets built. Mario

Jtrux · 01-09-2008, 08:08 PM

Quote:

Originally Posted by BLUE THUNDER

Congrats on the motor. I'm doing the same thing. Putting in a 305 while the 350 gets built. Mario

progress???

**Yukon Jack** · 01-10-2008, 05:18 AM

Help me remember, was this a basic rebuild or did you hop it up some? Congrats on getting it in and running.

Sure makes it easy to do with the front clip off.

BLUE THUNDER · 01-10-2008, 05:00 PM

Yeah, progress this weekend if you're not sleeping. Swing by if you get a chance.

WORNBRAKES · 01-10-2008, 05:25 PM

Hoped up a little Yukon. I had the block cleaned and honed and the crank had to be turned 10/20. I went with the Ram Jet cam that racinjason put me on. I cleaned and reused the internals. New aluminum intake and a Holly Truck Avenger 670cfm carb. Headers. 3 inch pipes and 40 series Flowmasters. I stabbed the old HEI with new wires.
I am planning on pulling the the dizy this weekend and replacing the gear with the softer one that is used with the vortecs. I am hopping that will finish the tune for me.
Here is the other thread.
http://67-72chevytrucks.com/vboard/s...d.php?t=247205
Oh yeah. removing the front clip is a must.

01-09-2008, 06:37 PM	#1
WORNBRAKES Senior Member Join Date: Jul 2001 Location: Hughesville, MD Posts: 1,350	new engine in K5 I have it installed and running. Still have some tunning to do with dizy and carb but I am happy with the upgrade so far. Aint she perty? Attached Images __________________ Mario and Mandy Hughesville, MD 20637 69 C10 305/350 71 K5 Basket case 75 K10 Rescue Parting out 77 MG Midget Parting out 15 6.7L Cummins

01-09-2008, 07:08 PM	#2
BLUE THUNDER Registered User Join Date: May 2007 Location: San Antonio Posts: 993	Re: new engine in K5 Congrats on the motor. I'm doing the same thing. Putting in a 305 while the 350 gets built. Mario

01-10-2008, 05:18 AM	#4
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Re: new engine in K5 Help me remember, was this a basic rebuild or did you hop it up some? Congrats on getting it in and running. Sure makes it easy to do with the front clip off. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

01-10-2008, 05:00 PM	#5
BLUE THUNDER Registered User Join Date: May 2007 Location: San Antonio Posts: 993	Re: new engine in K5 Yeah, progress this weekend if you're not sleeping. Swing by if you get a chance.

01-10-2008, 05:25 PM	#6
WORNBRAKES Senior Member Join Date: Jul 2001 Location: Hughesville, MD Posts: 1,350	Re: new engine in K5 Hoped up a little Yukon. I had the block cleaned and honed and the crank had to be turned 10/20. I went with the Ram Jet cam that racinjason put me on. I cleaned and reused the internals. New aluminum intake and a Holly Truck Avenger 670cfm carb. Headers. 3 inch pipes and 40 series Flowmasters. I stabbed the old HEI with new wires. I am planning on pulling the the dizy this weekend and replacing the gear with the softer one that is used with the vortecs. I am hopping that will finish the tune for me. Here is the other thread. http://67-72chevytrucks.com/vboard/s...d.php?t=247205 Oh yeah. removing the front clip is a must. __________________ Mario and Mandy Hughesville, MD 20637 69 C10 305/350 71 K5 Basket case 75 K10 Rescue Parting out 77 MG Midget Parting out 15 6.7L Cummins Last edited by WORNBRAKES; 01-10-2008 at 05:26 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.