|
10-30-2008, 10:20 PM
|
#1 |
|
Registered User
Join Date: Aug 2008
Location: Dexter, N.M.
Posts: 1,082
|
Bumper
I GOT A COUPLE OF QUESTIONS AND I KNOW I CAN GET MY ANSWERS HERE.
1- I PUT A 86 2WD BODY ON A 79 FRAME AND NEED TO PUT A FRONT BUMPER ON IT. DO I GET BUMPER FOR THE 86? WILL IT BOLT RITE UP? I PREFER THE 86 BUMPER. 2- THE ORIGINAL MOTOR IS A 4.3 LIT. V-6. WITH A SERPENTINE BELT SET-UP. CAN I TAKE IT OFF AND USE IT ON A 350? THANXS IN ADVANCE. 
__________________
Its Kool to be a square 2013 Chevy Silverado Z71 w/ 7" lift and 35" Nitto's 1985 C-10 ......My dream truck (under construction) 1984 k 10 Silverado...6" lift with 38.5 super swampers  New Mexico Member ---  Member of the Square Body Club--- 
|
|
|
|
10-30-2008, 11:35 PM
|
#2 |
|
Robert Olson Transport
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,280
|
Re: Bumper
im not sure about the serpentine system but i think there is a difference on the frames and you would need to cut it to make an 86 bumper fit.. CaptKaos would prolly know the correct answer
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
|
10-31-2008, 12:20 AM
|
#3 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,942
|
Re: Bumper
Front frame horns requiring trimming to allow the later model bumper to fit the pre-81 frame. The later model bumper will also contact the 73-80 style fenders for those out there wanting to go that direction.
The 4.3 accesory drive will fit a sbc V8. A 4.3 is basically a V8 w/the back two cylinders removed.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 10-31-2008 at 12:21 AM. |
|
|
|
10-31-2008, 12:36 AM
|
#4 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: Bumper
I have a 81-87 bumper on my 80 with just the brackets and frame mounts wallered out, i'm using the 73-80 L shaped bracket and the 81-87 braces
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 Last edited by flamingbig10; 10-31-2008 at 12:37 AM. |
|
|
|
|
10-31-2008, 02:09 PM
|
#5 |
|
Registered User
Join Date: Aug 2008
Location: Dexter, N.M.
Posts: 1,082
|
Re: Bumper
Thanx guys i knew u all could help me.
__________________
Its Kool to be a square 2013 Chevy Silverado Z71 w/ 7" lift and 35" Nitto's 1985 C-10 ......My dream truck (under construction) 1984 k 10 Silverado...6" lift with 38.5 super swampers New Mexico Member --- Member of the Square Body Club---
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
