|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-21-2009, 01:14 PM
|
#1 |
|
It's alsways something.....
 
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Need Steel floor section
I need the front drivers side steel floor section as seen in the pic below (its a short bed)- back to the wheel well (about 22-24") and over to about the center of the bed. It doesnt have to be show quality, just not rusty to the point that it coudlnt be welded in. I am having the dura liner/ line X or similar sprayed in after repaired.
Shipped to 30135 please, just email me at 14bama@bellsouth.net or PM |
|
|
|
04-21-2009, 01:53 PM
|
#2 |
|
Registered User
Join Date: Mar 2007
Location: spring grove, Pa.
Posts: 538
|
Re: Need Steel floor section
Does it have to be off of a shorty?
|
|
|
|
|
04-21-2009, 02:06 PM
|
#3 |
|
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: Need Steel floor section
We sell these
|
|
|
|
|
04-21-2009, 02:35 PM
|
#4 |
|
Registered User
Join Date: Mar 2007
Location: spring grove, Pa.
Posts: 538
|
Re: Need Steel floor section
never mind. I looked at the one I just took off and it is only a little better than yours. Later, Rich
|
|
|
|
|
04-22-2009, 08:11 AM
|
#5 |
|
It's alsways something.....
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Re: Need Steel floor section
ttt
|
|
|
|
|
04-23-2009, 06:41 PM
|
#6 |
|
It's alsways something.....
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Re: Need Steel floor section
ttt again
|
|
|
|
|
05-02-2009, 06:31 PM
|
#7 |
|
It's alsways something.....
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Re: Need Steel floor section
Just a piece out of a good floor will work at this point. About 24 x 30 or so, out of the center will work- anyone?
|
|
|
|
|
05-08-2009, 10:34 PM
|
#8 |
|
It's alsways something.....
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Re: Need Steel floor section
tttttt
|
|
|
|
|
05-08-2009, 11:28 PM
|
#9 |
|
Registered User
Join Date: Mar 2008
Location: Oklahoma city
Posts: 490
|
Re: Need Steel floor section
i just got a blazer that i am probably cutting up the back part of the bed is bad but the front part is pretty decent i could probably cut you a patch out but i am not sure what it is worth so i will have to get back to you on price. would that work for you though?
|
|
|
|
|
05-21-2009, 12:14 AM
|
#10 |
|
Registered User
Join Date: Mar 2008
Location: Oklahoma city
Posts: 490
|
Re: Need Steel floor section
did you ever get a piece that you needed?
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
