Check it out shop wheels - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RW71 · 07-30-2009, 08:13 PM

What do you think? Shop wheels cast in Aluminum.

spaseghost · 07-30-2009, 08:31 PM

id like to see a burnout with those, or would that be a melt out, or what?

68 short step · 07-30-2009, 10:38 PM

what do they weigh? did you buy or make them?

RW71 · 07-30-2009, 10:48 PM

I make the shop wheels if any one want's to know. I'm about to start a production run, just wanted to see if anyone has a interest in them. Not for sell yet.

RW71 · 07-30-2009, 10:59 PM

They weigh 20lb right now, I'm going to lighten them to around 10lb.

mclairmo · 07-31-2009, 12:50 AM

The problem is that these may damage an epoxy coated garage floor. I think that is why others make them in plastic. However, for the rest of us who cannot afford epoxy floors, these are perfect.

**N2TRUX** · 07-31-2009, 12:53 AM

Quote:

Originally Posted by RW71

I make the shop wheels if any one want's to know. I'm about to start a production run, just wanted to see if anyone has a interest in them. Not for sell yet.

Let me know if you decide to start selling them. I will get you set up...

RW71 · 07-31-2009, 08:43 PM

Ok here's what the Finished wheel will look like, got it down to 10 lb. The wheels are 24" and can be drilled to any lug pattern or multi lug patterns.

Musclerodz · 08-01-2009, 12:43 AM

have you load tested them to failure? I would hate to have one of the lightened ones fail and cause damage to a vehicle, that would be a liability issue for you

mclairmo · 08-01-2009, 01:26 AM

I would make those holes smaller to prevent failure. What if someone installs these on a fully loaded one ton with a big block and it crushes them while the guy is under it? Make sure these are idiot proof.

PanelDeland · 08-01-2009, 05:26 AM

mclairmo,there is no such thing as idiot proof.When something is made "Idiot Proof" a bigger idiot comes along.

**special-K** · 08-01-2009, 06:02 AM

I`m curious,what`s the point of "shop wheels"?Are they for people who can`t come up with old wheels and tires?it costs money to dispose of old tires and wheels must be stripped of tires to scrap them around here.And,some day I could always sell the wheels as they get harder to find.I`ll be dollying my frame to the exhaust guy and maybe another shop or two.
How about making plates that bolt to the hubs with casters on the bottom?Then you`d kill two birds with one stone.And,the problem with damaging a pretty floor is taken care of,too.

Lippyp · 08-01-2009, 06:25 AM

Castors sound like a much better idea to me, that way you can easily shove it sideways out of the way without having to lift it. I'd have thought an aluminium "wheel" like that will either wear the floor out or itself wear out pretty quickly if you have plain abrasive concrete, also I'd have thought with those bloody great big holes in them any sideways stress and they'd fracture. You can get wheel dollies/skates that sit under the tyres and enable you to shove the car sideways s I don't really see the point of the auminium ones above.

mclairmo · 08-01-2009, 10:39 AM

Quote:

Originally Posted by PanelDeland

mclairmo,there is no such thing as idiot proof.When something is made "Idiot Proof" a bigger idiot comes along.

You are correct, however, this thing looks dangerous to me and I would hate to see someone get hurt and OP become liable for it. Also, this style of "shop wheel" and the caster style are all already being produced by others and have been out there for some time now. You would need a ton of general liability insurance or product liability insurance before even attempting to market and sell this thing. One product liability, wrongful death or personal injury lawsuit and it could wipe you out.

RW71 · 08-01-2009, 07:32 PM

I worked in a Foundry for 20 years, I would not make it if it was Unsafe. Thanks for the Replys.

PBFAB.COM · 08-01-2009, 07:40 PM

Have you thought about making them in diameters that are more common for wheel/tire combos? like 27" or 29" or 31"? That way one would be able to set their vehicle up with the same diameter of tire combo they will be running, and have a better idea of stance and ground clearances.

**kev2809** · 08-01-2009, 09:03 PM

Quote:

Originally Posted by porterbuilt

Have you thought about making them in diameters that are more common for wheel/tire combos? like 27" or 29" or 31"? That way one would be able to set their vehicle up with the same diameter of tire combo they will be running, and have a better idea of stance and ground clearances.

good idea, much cheaper/easier than finding someone with the exact same wheel/tire size combo your looking for to mock up your suspension or something. is the truck supposed to roll around on these or does it just hold it up like jackstands? im curious, ive never seen these before.

mclairmo · 08-01-2009, 10:20 PM

Quote:

Originally Posted by RW71

I worked in a Foundry for 20 years, I would not make it if it was Unsafe. Thanks for the Replys.

No disrespect intended, but how do you know they are safe? I would assume that extensive load testing and field testing would be needed to verify. Not trying to rain on your parade and the product is beautiful, just want to make sure that you have smooth sailing with this new venture. Good luck.

**special-K** · 08-03-2009, 07:55 AM

They could always be left solid for anyone concerned about safety.They could be made with some type of rubber fitted over them,like a bicycle tire.

RW71 · 08-05-2009, 05:49 PM

So out of all you that have replyed to this thread, would you buy somthing like this ?

mclairmo · 08-05-2009, 06:56 PM

No. I've got wheels and tires already. When I paint, I just cover them up. On past projects, I always just used old roller tires/rims and then sold them when I was done with them. However, a professional shop that restores lots of these old vehicles might want to have these on hand as rollers since they take up much less space than tires/rims.

68 short step · 08-05-2009, 09:15 PM

$$$???

RW71 · 08-05-2009, 09:41 PM

The light ones will be around $350.00 for a set of four + shipping.

*Shane* · 08-05-2009, 10:27 PM

Quote:

Originally Posted by RW71

The light ones will be around $350.00 for a set of four + shipping.

seriously?

attack eagle · 08-05-2009, 11:55 PM

I'd just buy a set of used wheels and tires and pocket the extra $200, honestly.

plus I could DRIVE on those.

07-30-2009, 08:13 PM	#1
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Check it out shop wheels What do you think? Shop wheels cast in Aluminum. Attached Images

07-30-2009, 08:31 PM	#2
spaseghost certified tard Join Date: Jun 2009 Location: grand junction, colorado Posts: 182	Re: Check it out shop wheels id like to see a burnout with those, or would that be a melt out, or what?

07-30-2009, 10:38 PM	#3
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	Re: Check it out shop wheels what do they weigh? did you buy or make them?

07-30-2009, 10:48 PM	#4
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels I make the shop wheels if any one want's to know. I'm about to start a production run, just wanted to see if anyone has a interest in them. Not for sell yet.

07-30-2009, 10:59 PM	#5
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels They weigh 20lb right now, I'm going to lighten them to around 10lb.

07-31-2009, 12:50 AM	#6
mclairmo Registered User Join Date: Jan 2006 Location: Take Off Posts: 1,908	Re: Check it out shop wheels The problem is that these may damage an epoxy coated garage floor. I think that is why others make them in plastic. However, for the rest of us who cannot afford epoxy floors, these are perfect.

07-31-2009, 08:43 PM	#8
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels Ok here's what the Finished wheel will look like, got it down to 10 lb. The wheels are 24" and can be drilled to any lug pattern or multi lug patterns. Attached Images

08-01-2009, 12:43 AM	#9
Musclerodz Senior Member Join Date: Aug 2005 Location: OKC, OK Posts: 2,364	Re: Check it out shop wheels have you load tested them to failure? I would hate to have one of the lightened ones fail and cause damage to a vehicle, that would be a liability issue for you __________________ Mike Redpath

08-01-2009, 01:26 AM	#10
mclairmo Registered User Join Date: Jan 2006 Location: Take Off Posts: 1,908	Re: Check it out shop wheels I would make those holes smaller to prevent failure. What if someone installs these on a fully loaded one ton with a big block and it crushes them while the guy is under it? Make sure these are idiot proof.

08-01-2009, 05:26 AM	#11
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: Check it out shop wheels mclairmo,there is no such thing as idiot proof.When something is made "Idiot Proof" a bigger idiot comes along. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

08-01-2009, 06:02 AM	#12
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Check it out shop wheels I`m curious,what`s the point of "shop wheels"?Are they for people who can`t come up with old wheels and tires?it costs money to dispose of old tires and wheels must be stripped of tires to scrap them around here.And,some day I could always sell the wheels as they get harder to find.I`ll be dollying my frame to the exhaust guy and maybe another shop or two. How about making plates that bolt to the hubs with casters on the bottom?Then you`d kill two birds with one stone.And,the problem with damaging a pretty floor is taken care of,too. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 08-01-2009 at 06:03 AM.

08-01-2009, 06:25 AM	#13
Lippyp English Chevy Owner Join Date: May 2002 Location: Shropshire, UK/ Lot, France Posts: 1,848	Re: Check it out shop wheels Castors sound like a much better idea to me, that way you can easily shove it sideways out of the way without having to lift it. I'd have thought an aluminium "wheel" like that will either wear the floor out or itself wear out pretty quickly if you have plain abrasive concrete, also I'd have thought with those bloody great big holes in them any sideways stress and they'd fracture. You can get wheel dollies/skates that sit under the tyres and enable you to shove the car sideways s I don't really see the point of the auminium ones above. __________________ Phil '67 C10 long fleet. 350/TH350, 4 bbl Carter, K&N, Dual exhaust, loads of stuff coming soon 2001 S10 Blazer Daily Driver, bone stock 4 door 4x4 with manual transmission

08-01-2009, 07:32 PM	#15
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels I worked in a Foundry for 20 years, I would not make it if it was Unsafe. Thanks for the Replys.

08-01-2009, 07:40 PM	#16
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: Check it out shop wheels Have you thought about making them in diameters that are more common for wheel/tire combos? like 27" or 29" or 31"? That way one would be able to set their vehicle up with the same diameter of tire combo they will be running, and have a better idea of stance and ground clearances. __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!

08-03-2009, 07:55 AM	#19
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Check it out shop wheels They could always be left solid for anyone concerned about safety.They could be made with some type of rubber fitted over them,like a bicycle tire. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~



Register or Log In To remove these advertisements.

08-05-2009, 05:49 PM	#20
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels So out of all you that have replyed to this thread, would you buy somthing like this ?

08-05-2009, 06:56 PM	#21
mclairmo Registered User Join Date: Jan 2006 Location: Take Off Posts: 1,908	Re: Check it out shop wheels No. I've got wheels and tires already. When I paint, I just cover them up. On past projects, I always just used old roller tires/rims and then sold them when I was done with them. However, a professional shop that restores lots of these old vehicles might want to have these on hand as rollers since they take up much less space than tires/rims.

08-05-2009, 09:15 PM	#22
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	Re: Check it out shop wheels $$$???

08-05-2009, 09:41 PM	#23
RW71 Registered User Join Date: Jan 2009 Location: Springfield, Oregon Posts: 84	Re: Check it out shop wheels The light ones will be around $350.00 for a set of four + shipping.

08-05-2009, 11:55 PM	#25
attack eagle Registered User Join Date: Feb 2008 Location: El Paso TX Posts: 76	Re: Check it out shop wheels I'd just buy a set of used wheels and tires and pocket the extra $200, honestly. plus I could DRIVE on those.

Register or Log In To remove these advertisements.