paging 1faastc10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Tom · 01-13-2003, 03:42 PM

Hey jermey, you work at a Gm parts counter dont you? Im looking for the bushings for a 1 1/4" sway bar [off a c30] and the bracket for one side to hold it to the a-arm. Can you find those part numbers?

PHOENIX · 01-13-2003, 04:08 PM

Tom:
About the bushings, have you tried contacting (http://www.performancesuspension.com/) they are located on 35th avenue just north of Thomas on the east side of the road (isnt that on your way home from work, kinda?).

Tom · 01-13-2003, 05:20 PM

yeah it kinda is. Well about a mile out of the way, but no biggie. So is the closest Gm dealership.
I doubt they will have the bracket, but some poly bushings would be nice. Ill give em a "holla"

*1FaastC10* · 01-13-2003, 07:04 PM

nope Tom, i gave up the counter about 2 months ago in favor of a factory job. was a tough decision, especially considering all of the info i was getting, and parts at 15% over cost(retail is 67-100%, sometimes more). im glad i switched though, not as many idiots to deal with over the counter, makes my life a whole lot easier.

*1FaastC10* · 01-13-2003, 07:05 PM

ask Brandon about the brackets that hold them to the arm... i think i gave him the part number a few months back.

Tom · 01-14-2003, 12:18 AM

Was brandons a 1 1/8" or 1 1/4" bar?
I hear ya on givin up the parts counter, I wouldnt want to stay there for long either

79BIG10 · 01-14-2003, 04:53 AM

Tom mine was a 1 1/16 bar. This may get you in the ball park close to where they need to be. The sway bar brackets mount to that frame bracket part #6271375 $9.49 a piece.You could go to a junk yard looking but be warned that they're hard to take of since they're riveted on. I mounted mine on with 3/8x1 1/2" grade 8 bolts, washer, lock washer and nut. I went and got the Moog ply bushings cheap (will replace with greaseable with front end later). The brackets part #334671 for a 1 1/16" bar for $4.29? a piece.

01-13-2003, 03:42 PM	#1
Tom driving is in my blood Join Date: Dec 1999 Location: Mesa AZ Posts: 5,720	paging 1faastc10 Hey jermey, you work at a Gm parts counter dont you? Im looking for the bushings for a 1 1/4" sway bar [off a c30] and the bracket for one side to hold it to the a-arm. Can you find those part numbers? __________________ -78 c10 short/step: 388cid, M20, 5/5 drop, lots more. Playtoy and first vehicle. -98 c1500 x-cab: 5.7L, 17" rims, 5/6 drop, flowmaster, helper bags,NBS rear disk brakes. -02 Suburban 4x4: leveled front -CBR600F4i, CBR600RR, CBR1000RR, and standup skis DISCLAIMER: I cant spell for the life of me.

01-13-2003, 04:08 PM	#2
PHOENIX Registered User Join Date: Oct 2002 Location: Phoenix, Arizona Posts: 4,703	Tom: About the bushings, have you tried contacting (http://www.performancesuspension.com/) they are located on 35th avenue just north of Thomas on the east side of the road (isnt that on your way home from work, kinda?). __________________ * AVOID: LOPER'S PERMORANCE / LOPERSPEED.COM OF PHOENIX, AZ & COTTMAN TRANSMISSION *

01-14-2003, 04:53 AM	#7
79BIG10 I'm back with 2nd truck! Join Date: Feb 2002 Location: Texas Posts: 3,775	Tom mine was a 1 1/16 bar. This may get you in the ball park close to where they need to be. The sway bar brackets mount to that frame bracket part #6271375 $9.49 a piece.You could go to a junk yard looking but be warned that they're hard to take of since they're riveted on. I mounted mine on with 3/8x1 1/2" grade 8 bolts, washer, lock washer and nut. I went and got the Moog ply bushings cheap (will replace with greaseable with front end later). The brackets part #334671 for a 1 1/16" bar for $4.29? a piece. __________________ 1979 Chevrolet Bonanza Big10 "Tootsie Roll" 1985 Chevrolet Silverado (wife's) Member of the Southern Bowties Club "Don't underestimate how sexy a fat man who drinks to excess can be." Homer Simpson

01-13-2003, 05:20 PM	#3
Tom driving is in my blood Join Date: Dec 1999 Location: Mesa AZ Posts: 5,720	yeah it kinda is. Well about a mile out of the way, but no biggie. So is the closest Gm dealership. I doubt they will have the bracket, but some poly bushings would be nice. Ill give em a "holla" __________________ -78 c10 short/step: 388cid, M20, 5/5 drop, lots more. Playtoy and first vehicle. -98 c1500 x-cab: 5.7L, 17" rims, 5/6 drop, flowmaster, helper bags,NBS rear disk brakes. -02 Suburban 4x4: leveled front -CBR600F4i, CBR600RR, CBR1000RR, and standup skis DISCLAIMER: I cant spell for the life of me.

01-13-2003, 07:04 PM	#4
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,400	nope Tom, i gave up the counter about 2 months ago in favor of a factory job. was a tough decision, especially considering all of the info i was getting, and parts at 15% over cost(retail is 67-100%, sometimes more). im glad i switched though, not as many idiots to deal with over the counter, makes my life a whole lot easier.

01-13-2003, 07:05 PM	#5
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,400	ask Brandon about the brackets that hold them to the arm... i think i gave him the part number a few months back.

01-14-2003, 12:18 AM	#6
Tom driving is in my blood Join Date: Dec 1999 Location: Mesa AZ Posts: 5,720	Was brandons a 1 1/8" or 1 1/4" bar? I hear ya on givin up the parts counter, I wouldnt want to stay there for long either __________________ -78 c10 short/step: 388cid, M20, 5/5 drop, lots more. Playtoy and first vehicle. -98 c1500 x-cab: 5.7L, 17" rims, 5/6 drop, flowmaster, helper bags,NBS rear disk brakes. -02 Suburban 4x4: leveled front -CBR600F4i, CBR600RR, CBR1000RR, and standup skis DISCLAIMER: I cant spell for the life of me.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.