TX Selling one project to make room for the other - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jholley · 10-28-2009, 07:01 PM

I have a complete rolling 69 SWB chassis with a TON of work done on it that I'm going to sell to make room for my 72 I just got not long ago. I'd like to sell the chassis whole but if there isn't any interest I'll probably part it out at a later date. Here is a list of parts and what has been done.

The chassis was stripped, c-notched (weld in), primed and powdercoated. All of the suspension pieces, front and rear were stripped and powdercoated.

Parts, starting at the front...

Front Crossmember is new
New POL Tubular SB motor mounts
All new ball joints/tie rod ends
New cross shafts upper and lower
ECE 2.5" drop spindles
New front rotors
New front calipers (5 lug)
New wheel bearings/seals
New CPP tubular trans crossmember
New ECE drop center crossmember
New trailing arm bushings
New rear shock relocators
New CPP 2" drop blocks
New KYB Shocks all around 2/4 drop
New CPP 2" drop springs (front)
New CPP 4" drop springs (rear)
New CPP C-notches
New custom built driveshaft
New POL 19 gallon baffled aluminum fuel tank w/sender
New CPP curved panhard bar
New rear crossmember
3.07 Posi rear end w/disc brakes (5 lug) cleaned/painted
New Glocks rear caliper mounts
New rear impala rotors
Rear camaro calipers
Steering Box
1 1/8 front sway bar

All of the parts and powdercoating cost alone total up to better than $3700. I can e-mail a list of what I paid for all this stuff if anyone is interested. That $3700 doesn't figure in any labor or shipping costs either.

I'd like to get $3000 for it.

This is a quality piece that will save somebody a ton of time on their project. All of the hard work is already done. Run some plumbing on it and put a body and a motor on it and your done. I'll include a set of wheels and tires to roll it around with. Oh and I can provide a good title and cab VIN plates with it too.

jholley · 10-28-2009, 07:06 PM

Here are a couple more pics. If anybody wants pics of anything in particular, let me know.

jholley · 10-28-2009, 07:09 PM

The rallys in the pic don't go with the truck, the ones in this pic do. (I have all four hub caps) I also have some extras that I'll throw in with the truck including a passenger side SWB fleet bedside, a bench seat, a hood (if I still have it) and a box of door hinges, hood hinges and some other odds and ends.

**kev2809** · 10-28-2009, 07:15 PM

if you decide to part it out, how much for the spindles and would they fit my 67 suburban? thanks...nice work btw

jholley · 10-28-2009, 07:17 PM

I haven't individually priced anything yet. I'm going to give this some time to simmer first because it's a lot less hassle than boxing all this stuff up and ship it then be left with a non-rolling frame. As far as know they will fit your Suburban but I'm not the expert here. They are set up for disc brakes though, not sure if yours is. I'm sure one of the big brains will know if they will fit. I'll give you a shout back when/if parting out time happens.

coast2coast · 10-28-2009, 07:23 PM

I wish you luck on selling it complete. Sounds like a deal considering all the good parts and labor in it. But if you decide to part it, I'd be interested in the POL Tubular SB motor mounts and the CPP curved panhard bar, pending prices.

dk1972 · 10-28-2009, 07:23 PM

if you part out or would you just wanna sell me the tailgate off the orche lwb?

jholley · 10-28-2009, 07:42 PM

Nothing on the 72 is for sale. I just put that pic up to show the wheels and caps that will go with the chassis. Thanks though.

VA72C10 · 10-28-2009, 08:10 PM

best wishes on the sale...that's a really good deal and would be perfect for someone getting ready to start a project or frame off...save them a ton of time and money...

dk1972 · 10-28-2009, 08:27 PM

oh ok then thanks

**kev2809** · 10-28-2009, 08:40 PM

Quote:

Originally Posted by jholley

I haven't individually priced anything yet. I'm going to give this some time to simmer first because it's a lot less hassle than boxing all this stuff up and ship it then be left with a non-rolling frame. As far as know they will fit your Suburban but I'm not the expert here. They are set up for disc brakes though, not sure if yours is. I'm sure one of the big brains will know if they will fit. I'll give you a shout back when/if parting out time happens.

mine do have disc brakes. just pm me if you decide to...i dont check the for sale threads all that much. thanks

budder71 · 10-28-2009, 08:47 PM

I have a 72 LWB rolling chassis that has many of the same things done to, sandblasted/powdercoated, new front end, new brake all around, rear end gone through, etc, would you be willing to trade and me give some cash to boot ?

jholley · 10-28-2009, 09:10 PM

I'm not really looking for another one. I have three now. I'm trying to get rid of one. I appreciate the offer though.

72BlckButy · 10-28-2009, 09:14 PM

Jim, that is a smokin' deal... good luck with the sale!

budder71 · 10-28-2009, 09:20 PM

how much lower than stock will the body/chassis sit once assembled on this chassis ?

jholley · 10-28-2009, 09:23 PM

4.5" in the front, 6" in the back. I goofed in the original post the blocks are 2" not 1". It should be pretty much level

budder71 · 10-28-2009, 09:25 PM

if you don't get any bites and you could take a trade and some cash I would like to offer $1200.00 and the LWB chassis with bed and tailgate that I have..

Spray-Bomb · 10-28-2009, 11:45 PM

Its nice, Ive seen it

67c-10Texas · 10-29-2009, 05:22 PM

interested in the fuel tank if parted out

im in san marcos

jholley · 10-29-2009, 05:43 PM

Ok. If I decide to part I'll give you a shout.

budder71 · 10-29-2009, 09:51 PM

sure wish you could use this LIKE NEW LWB chassis with bed and some cash.....

jholley · 10-29-2009, 10:00 PM

Man I hear ya. It's just that I have a good solid 72 LWB that I'm really not interested in doing anything with other than making it mechanically sound and driving the hell out of it. I've already done the front end rebuild and brakes. I'm putting a motor and trans in it and I'm done. I do appreciate the offer but I'm just not going that direction with this truck.

I am getting ready to make a little road trip across I-10 to FLA in a couple weeks though. If you bought mine we could work something out on delivery.

budder71 · 10-29-2009, 10:21 PM

if you have time right now just give me a call to discuss some things about your chassis.... I am a little green at this, the lowering and such, and I have a few questions...
601 270 1769
George Davis

Southern C10 · 10-30-2009, 07:46 PM

PM sent

jholley · 10-31-2009, 01:06 PM

Chassis is sold.

10-28-2009, 07:01 PM	#1
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Selling one project to make room for the other I have a complete rolling 69 SWB chassis with a TON of work done on it that I'm going to sell to make room for my 72 I just got not long ago. I'd like to sell the chassis whole but if there isn't any interest I'll probably part it out at a later date. Here is a list of parts and what has been done. The chassis was stripped, c-notched (weld in), primed and powdercoated. All of the suspension pieces, front and rear were stripped and powdercoated. Parts, starting at the front... Front Crossmember is new New POL Tubular SB motor mounts All new ball joints/tie rod ends New cross shafts upper and lower ECE 2.5" drop spindles New front rotors New front calipers (5 lug) New wheel bearings/seals New CPP tubular trans crossmember New ECE drop center crossmember New trailing arm bushings New rear shock relocators New CPP 2" drop blocks New KYB Shocks all around 2/4 drop New CPP 2" drop springs (front) New CPP 4" drop springs (rear) New CPP C-notches New custom built driveshaft New POL 19 gallon baffled aluminum fuel tank w/sender New CPP curved panhard bar New rear crossmember 3.07 Posi rear end w/disc brakes (5 lug) cleaned/painted New Glocks rear caliper mounts New rear impala rotors Rear camaro calipers Steering Box 1 1/8 front sway bar All of the parts and powdercoating cost alone total up to better than $3700. I can e-mail a list of what I paid for all this stuff if anyone is interested. That $3700 doesn't figure in any labor or shipping costs either. I'd like to get $3000 for it. This is a quality piece that will save somebody a ton of time on their project. All of the hard work is already done. Run some plumbing on it and put a body and a motor on it and your done. I'll include a set of wheels and tires to roll it around with. Oh and I can provide a good title and cab VIN plates with it too. Attached Images __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S Last edited by jholley; 10-28-2009 at 09:26 PM.

10-28-2009, 07:06 PM	#2
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other Here are a couple more pics. If anybody wants pics of anything in particular, let me know. Attached Images __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S

10-28-2009, 07:09 PM	#3
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other The rallys in the pic don't go with the truck, the ones in this pic do. (I have all four hub caps) I also have some extras that I'll throw in with the truck including a passenger side SWB fleet bedside, a bench seat, a hood (if I still have it) and a box of door hinges, hood hinges and some other odds and ends. Attached Images __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S Last edited by jholley; 10-28-2009 at 07:12 PM.

10-28-2009, 07:15 PM	#4
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,144	Re: Selling one project to make room for the other if you decide to part it out, how much for the spindles and would they fit my 67 suburban? thanks...nice work btw __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

10-28-2009, 07:17 PM	#5
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other I haven't individually priced anything yet. I'm going to give this some time to simmer first because it's a lot less hassle than boxing all this stuff up and ship it then be left with a non-rolling frame. As far as know they will fit your Suburban but I'm not the expert here. They are set up for disc brakes though, not sure if yours is. I'm sure one of the big brains will know if they will fit. I'll give you a shout back when/if parting out time happens. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S Last edited by jholley; 10-28-2009 at 07:56 PM.

10-28-2009, 07:23 PM	#6
coast2coast Registered User Join Date: Oct 2006 Location: Strafford Missouri Posts: 217	Re: Selling one project to make room for the other I wish you luck on selling it complete. Sounds like a deal considering all the good parts and labor in it. But if you decide to part it, I'd be interested in the POL Tubular SB motor mounts and the CPP curved panhard bar, pending prices.

10-28-2009, 07:23 PM	#7
dk1972 Registered User Join Date: Oct 2009 Location: phoenix arizona Posts: 93	Re: Selling one project to make room for the other if you part out or would you just wanna sell me the tailgate off the orche lwb? __________________ 1972 Cheyenne super 20 original

10-28-2009, 07:42 PM	#8
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other Nothing on the 72 is for sale. I just put that pic up to show the wheels and caps that will go with the chassis. Thanks though. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S

10-28-2009, 08:10 PM	#9
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Selling one project to make room for the other best wishes on the sale...that's a really good deal and would be perfect for someone getting ready to start a project or frame off...save them a ton of time and money... __________________ Looking for a 67-72 swb or blazer project in or around VA.

10-28-2009, 08:27 PM	#10
dk1972 Registered User Join Date: Oct 2009 Location: phoenix arizona Posts: 93	Re: Selling one project to make room for the other oh ok then thanks __________________ 1972 Cheyenne super 20 original

10-28-2009, 08:47 PM	#12
budder71 Registered User Join Date: Jul 2009 Location: Hattiesburg Mississippi Posts: 697	Re: Selling one project to make room for the other I have a 72 LWB rolling chassis that has many of the same things done to, sandblasted/powdercoated, new front end, new brake all around, rear end gone through, etc, would you be willing to trade and me give some cash to boot ?

10-28-2009, 09:10 PM	#13
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other I'm not really looking for another one. I have three now. I'm trying to get rid of one. I appreciate the offer though. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S

10-28-2009, 09:14 PM	#14
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Selling one project to make room for the other Jim, that is a smokin' deal... good luck with the sale! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

10-28-2009, 09:20 PM	#15
budder71 Registered User Join Date: Jul 2009 Location: Hattiesburg Mississippi Posts: 697	Re: Selling one project to make room for the other how much lower than stock will the body/chassis sit once assembled on this chassis ?

10-28-2009, 09:23 PM	#16
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other 4.5" in the front, 6" in the back. I goofed in the original post the blocks are 2" not 1". It should be pretty much level __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S Last edited by jholley; 10-28-2009 at 09:27 PM.



Register or Log In To remove these advertisements.

10-28-2009, 09:25 PM	#17
budder71 Registered User Join Date: Jul 2009 Location: Hattiesburg Mississippi Posts: 697	Re: Selling one project to make room for the other if you don't get any bites and you could take a trade and some cash I would like to offer $1200.00 and the LWB chassis with bed and tailgate that I have..

10-28-2009, 11:45 PM	#18
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: Selling one project to make room for the other Its nice, Ive seen it __________________ Just not low enough... ----------------------------- Sinister Killer

10-29-2009, 05:22 PM	#19
67c-10Texas Registered User Join Date: Apr 2006 Location: Texas Posts: 259	Re: Selling one project to make room for the other interested in the fuel tank if parted out im in san marcos

10-29-2009, 05:43 PM	#20
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other Ok. If I decide to part I'll give you a shout. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S

10-29-2009, 09:51 PM	#21
budder71 Registered User Join Date: Jul 2009 Location: Hattiesburg Mississippi Posts: 697	Re: Selling one project to make room for the other sure wish you could use this LIKE NEW LWB chassis with bed and some cash.....

10-29-2009, 10:00 PM	#22
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other Man I hear ya. It's just that I have a good solid 72 LWB that I'm really not interested in doing anything with other than making it mechanically sound and driving the hell out of it. I've already done the front end rebuild and brakes. I'm putting a motor and trans in it and I'm done. I do appreciate the offer but I'm just not going that direction with this truck. I am getting ready to make a little road trip across I-10 to FLA in a couple weeks though. If you bought mine we could work something out on delivery. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S Last edited by jholley; 10-29-2009 at 10:02 PM.

10-29-2009, 10:21 PM	#23
budder71 Registered User Join Date: Jul 2009 Location: Hattiesburg Mississippi Posts: 697	Re: Selling one project to make room for the other if you have time right now just give me a call to discuss some things about your chassis.... I am a little green at this, the lowering and such, and I have a few questions... 601 270 1769 George Davis

10-30-2009, 07:46 PM	#24
Southern C10 Is it done yet? Join Date: Apr 2008 Location: Whispering Pines, NC Posts: 826	Re: Selling one project to make room for the other PM sent __________________ 1972 Chevy SWB New 383 Stroker/350 Turbo Some day i'll paint it John 3:16 MY BUILD THREAD http://67-72chevytrucks.com/vboard/s...d.php?t=398108

10-31-2009, 01:06 PM	#25
jholley Registered User Join Date: Jul 2008 Location: TX Posts: 737	Re: Selling one project to make room for the other Chassis is sold. __________________ ------------------------------------------------- Jim Garage fillers... 85 Chevy C10 Silverado LWB 07 Nissan Altima 2006 Mini Cooper S

Register or Log In To remove these advertisements.