GA 350 Corvette Engine - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**bigunde** · 12-05-2009, 12:30 PM

Selling a 1984 Corvette 350. It was rebuilt a few years back and not alot miles put on it since then. It is the 207 casting block. Complete from 4 barrel intake to oil pan. It is the ZFC code engine.. Asking $350

**kev2809** · 12-05-2009, 01:37 PM

damn if you were in houston i would take it...good luck with the sell

**bigunde** · 12-06-2009, 05:37 PM

Quote:

Originally Posted by kev2809

damn if you were in houston i would take it...good luck with the sell

hehe Thank ya sir.

Byronic · 12-06-2009, 07:44 PM

How far from Panama City, FL? Any info on the build?

young grasshoppa · 12-09-2009, 06:53 PM

bump, is this still available? What city are you in?

**bigunde** · 12-15-2009, 07:54 PM

It was rebuilt back stock with a small cam. I am located in Alma, Ga.. Sorry for the delay. Sometimes the site doesnt sent notifications of any replies.

*Dylan · 12-17-2009, 01:10 AM

Do you know any specifics on the engine? Did it run when pulled? How long ago was it pulled? What is the significance of the ZFC code and the 207 casting? Do you know the horsepower and torque ratings or anything for these engines? Is everything there ready for me to drop it into my truck? If not what else would be required to get it in my truck and running? If I were to come pick it up, do you have a hoist that we could use to get it into the back of my truck?

Thanks,
Dylan.

**bigunde** · 12-18-2009, 10:25 AM

Quote:

Originally Posted by *Dylan

Do you know any specifics on the engine? Did it run when pulled? How long ago was it pulled? What is the significance of the ZFC code and the 207 casting? Do you know the horsepower and torque ratings or anything for these engines? Is everything there ready for me to drop it into my truck? If not what else would be required to get it in my truck and running? If I were to come pick it up, do you have a hoist that we could use to get it into the back of my truck?

Thanks,
Dylan.

Dylan, here are the factory specs

Type ohv V-8

Displacement, liters/cubic inch
5.7/350
Bore X stroke, inches 4.00 X 3.48
Fuel management
Cross-Fire Throttle Body Fuel Injection
Horsepower @ rpm
205 @ 4,300

Torque @ rpm, pound-foot
290 @ 2,800

It now has a small cam and 4 barrel intake. It is complete from intake to oil pan but with no accessories (pretty much a long block), Ill test fire it on the engine stand again tomorrow and make sure all is well with it.

*Dylan · 12-18-2009, 09:08 PM

Alright, thanks!

12-05-2009, 12:30 PM	#1
bigunde Rusty Rockerfeller Join Date: May 2003 Location: South Georgia Posts: 1,631	350 Corvette Engine Selling a 1984 Corvette 350. It was rebuilt a few years back and not alot miles put on it since then. It is the 207 casting block. Complete from 4 barrel intake to oil pan. It is the ZFC code engine.. Asking $350

12-05-2009, 01:37 PM	#2
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,146	Re: 350 Corvette Engine damn if you were in houston i would take it...good luck with the sell __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

12-06-2009, 07:44 PM	#4
Byronic The Beach Cruiser Join Date: May 2009 Location: Panama City, Florida Posts: 358	Re: 350 Corvette Engine How far from Panama City, FL? Any info on the build? __________________ 1999 Silverado DD 1966 Panel Truck 2003 Harley Road Glide 1967 Schwinn Tandem Single Speed

12-09-2009, 06:53 PM	#5
young grasshoppa Registered User Join Date: Nov 2006 Location: OKC, OK Posts: 88	Re: 350 Corvette Engine bump, is this still available? What city are you in?

12-15-2009, 07:54 PM	#6
bigunde Rusty Rockerfeller Join Date: May 2003 Location: South Georgia Posts: 1,631	Re: 350 Corvette Engine It was rebuilt back stock with a small cam. I am located in Alma, Ga.. Sorry for the delay. Sometimes the site doesnt sent notifications of any replies.

12-17-2009, 01:10 AM	#7
*Dylan Mean Buzzin' Half Dozen Join Date: Mar 2008 Location: Orlando, Florida Posts: 1,081	Re: 350 Corvette Engine Do you know any specifics on the engine? Did it run when pulled? How long ago was it pulled? What is the significance of the ZFC code and the 207 casting? Do you know the horsepower and torque ratings or anything for these engines? Is everything there ready for me to drop it into my truck? If not what else would be required to get it in my truck and running? If I were to come pick it up, do you have a hoist that we could use to get it into the back of my truck? Thanks, Dylan. __________________ "War is an ugly thing, but not the ugliest of things. The decayed and degraded state of moral and patriotic feeling which thinks that nothing is worth war is much worse. The person who has nothing for which he is willing to fight, nothing which is more important than his own personal safety, is a miserable creature and has no chance of being free unless made and kept so by the exertions of better men than himself." MY TRUCK (Now for sale) 1967 C10 SWB *Dylan* IIMY?

12-18-2009, 09:08 PM	#9
*Dylan Mean Buzzin' Half Dozen Join Date: Mar 2008 Location: Orlando, Florida Posts: 1,081	Re: 350 Corvette Engine Alright, thanks! __________________ "War is an ugly thing, but not the ugliest of things. The decayed and degraded state of moral and patriotic feeling which thinks that nothing is worth war is much worse. The person who has nothing for which he is willing to fight, nothing which is more important than his own personal safety, is a miserable creature and has no chance of being free unless made and kept so by the exertions of better men than himself." MY TRUCK (Now for sale) 1967 C10 SWB *Dylan* IIMY?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.