|
02-23-2003, 09:11 PM
|
#1 |
|
Registered User
Join Date: Dec 2002
Location: Summerfield, Ks
Posts: 741
|
intake
A friend of mine sandblasted an aluminum intake cuz it was painted yellow and i was wondering if there is anything out there to put over it like in a spray can to protect it, i was thinkin clear coat but wouldn't that burn off???any ideas appreciated.
thanks kevin
__________________
1970 Chevy CST/10 1970 Chevy CST/10 1972 Chevy C/10 1972 Chevy Suburban K/10 2019 Silverado 2500 Duramax Kevin |
|
|
|
02-23-2003, 09:14 PM
|
#2 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,856
|
Shops that powdercoat intakes also use clearcoat!
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
02-23-2003, 09:17 PM
|
#3 |
|
Registered User
Join Date: Feb 2003
Location: Bremerton, WA
Posts: 86
|
Are you sure it is aluminum?
Most aluminum intakes are not painted but have some sort of varnish that makes them easier to clean. Because aluminum does not rust, you probably do not need anything on your intake. (Rust only occurs in the presence of iron) 
__________________
'72 GMC C20, "2500 Super Custom", Custom Camper, New 454 '93 K2500 Suburban, Old 454 (157K) |
|
|
|
|
02-23-2003, 09:29 PM
|
#4 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
getting it powdercoated is the best way to go but if moneys tight Easwood company sells a rattle can to do the job or por15 also has a suitable product but definately coat it cause aluminium doesn't stay nice for long
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
02-23-2003, 09:30 PM
|
#5 |
|
Registered User
Join Date: Dec 2002
Location: Summerfield, Ks
Posts: 741
|
yes im sure its aluminum and it was an ugly yellow, is there anything else i should put on there??
kevin
__________________
1970 Chevy CST/10 1970 Chevy CST/10 1972 Chevy C/10 1972 Chevy Suburban K/10 2019 Silverado 2500 Duramax Kevin |
|
|
|
|
02-23-2003, 09:33 PM
|
#6 |
|
Used to have a truck
Join Date: May 2002
Location: port orchard WA
Posts: 1,552
|
Clear paint in the rattle can will work fine. The intake doesnt get hot enough to burn the paint. It would if the heat riser were working 100% but the heat riser really only works effectively if you are using the cast iron exhaust manifolds with the thermostatic exhaust valve. I dont know anyone that does although the purists might ...but then again they wouldnt be using an aluminum manifold either. Without the exhaust valve you wont get enough exhaust gases through the manifold to get it hot enough to scorch the paint . Painting it clear makes keeping the aluminum clean much easier .
__________________
No truck :-( |
|
|
|
|
02-23-2003, 10:04 PM
|
#7 |
|
Registered User
Join Date: Sep 2002
Location: upland, california
Posts: 146
|
They make high temp clear that is used for engines, i used it on my intake and no problems so far!
|
|
|
|
|
02-24-2003, 01:04 AM
|
#8 |
|
Registered User
Join Date: Sep 2000
Location: huntington,texas,united states
Posts: 399
|
yea you can buy some hight heat paint made by vht. this stuff also has a high resistants to gasoline.
__________________
1972 chevy long bed. Currently under construction!! Bagged, 383/700r4. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
