MS 93-97 F-body Calipers for rear disk conversion.

[usmcchevy]

Were on a running and driving car earlier this year. Complete with all hardware, e-brake cables and brackets that came off the car. SOLD
I was going to use these with CaptinFab's brackets for rear disks, but decided to go another route. Heres a link to his brackets.
http://67-72chevytrucks.com/vboard/s...d.php?t=382633

[usmcchevy]

Ttt

[usmcchevy]

Offers?

[qksilver]

A question, it looks like those brackets would work on a 10 bolt truck rear. Any ides if they would? Is it a matter of the calipers too far in or out from the flange to work?

I am poor and cheap.......lol. Might make a deal if the brackets would work.

Thanks, pm me because I am forgetful too.

Steve

[WIDESIDE72]

hmmm... I am trying to decide which way to go on brakes. I have a complete rear axle out of a 94 Caprice 9c1, but I see that Captainfab says that if I run the Caprice caliper, there will be no e brke, which leads me back to these...

[usmcchevy]

Originally Posted by qksilver

A question, it looks like those brackets would work on a 10 bolt truck rear. Any ides if they would? Is it a matter of the calipers too far in or out from the flange to work?

I am poor and cheap.......lol. Might make a deal if the brackets would work.

Thanks, pm me because I am forgetful too.

Steve

No idea for sure, but you might be on to something. Even if the center hole is a bit small it could be opened up and as long as you use a rotor the same size as the f-body the bracket should put the caliper at the correct distance from the center of the axle. Like you said the only problem I can see would be the caliper being placed too far in or out. I'll measure the axle brackets tonight when I get home and post up the measurements.

Originally Posted by WIDESIDE72

hmmm... I am trying to decide which way to go on brakes. I have a complete rear axle out of a 94 Caprice 9c1, but I see that Captainfab says that if I run the Caprice caliper, there will be no e brke, which leads me back to these...

And these even come with good e-brake cables!

[qksilver]

thanks.........there was an option package for I can't remember what year but it was something like 1le used for racing. it used a 5x5 bolt pattern. I am thinking tht it might all work together. Let me know

Thanks,
Steve

[usmcchevy]

Ok, The center hole has a step in it, so one side measures 72mm and the other side measures 70mm.
The 4 mounting holes are not square by anymeans. As you are looking at the picture the top set of holes and the bottom set of holes are 2 and 7/16 apart. the two holes to the left of the picture are 3 and 1/16 apart and the set of holes to the right are 2 and 5/8" apart. If this doesn't make sense let me know.

[qksilver]

Cool, I will be out at my shop in the morning. My wife doesn't let me keep anything at home. Will let you know when I get home.

Thanks,
Steve

[qksilver]

I checked out a couple of rears at my shop. They will work on the 10 bolts i have but won't work on what I wanted discs on. Thanks for the measurements but i can't use them with some other brackets etc which puts it out of my budget.

Thanks again,
Steve

[usmcchevy]

TTT still have them, open to offers.

[usmcchevy]

Price drop $75 Shipped!

[usmcchevy]

Up!

[N2GMTrux]

If you would take $60 shipped I'll take them... Just pm your paypal,,,

Thanks
S.C.
Posted via Mobile Device

[mickeymouse]

If it gets to me, I will take them for 75 shipped.

[usmcchevy]

Originally Posted by N2GMTrux

If you would take $60 shipped I'll take them... Just pm your paypal,,,

Thanks
S.C.
Posted via Mobile Device

Thanks for the offer, but I'll have to pass.

Originally Posted by mickeymouse

If it gets to me, I will take them for 75 shipped.

SOLD pending payment. Sending PM with payment info.

[mickeymouse]

Paypal sent.

[usmcchevy]

Payment received and parts shipped!