TX GMC:Hydramatic Parts

[1956cameo]

I have a nearly complete Hydramatic set up for a 55-59 GMC. I have the carburator/linkage, shift linkage, transmission, cross member, bell housing, torque converter, flywheel, steering column/linkage. The only part that I think I am missing is the starter. I would like to sell this as a complete set up only. This was all pulled out of a non running vehicle and all parts will need to be overhauled. If anyone is interested I will take pictures and post them on here.

The price is $600 for everything I have. I am also very interested in trading all of these parts for a complete Chevy Hydramatic set up for a 55-59 truck. I am located just south of Houston, TX.

[Big Port Jimmy 6]

V8 or six cylinder?

[1956cameo]

Sorry I forgot they are different. My parts are from a V/8 truck. The Chevy parts that I need are also for a v/8 truck.

[Andy_Napco]

Hi, was curious if you still had these items for sale?

[1956cameo]

Andy Napco, Yes the parts are still for sale or trade! Just let me know and I can post some pics for you.

[Andy_Napco]

I'm in need of the shift linkages and the bell crank that bolts to the intake manifold. Bell crank to carb rod, bell crank to tranny (should have a spring with it, attaches to a tab on the tranny) and have a threaded end with a couple adjustable nuts. Would also like the lever off the tranny. Would also like to have the rod which goes from steering column to tranny to select gears.

Thanks,
Andy Taylor

[1956cameo]

I will try to post pictures of the linkages for you soon. From what I can tell I should have everything.

[Andy_Napco]

Sounds great, if you like or its easier you can send the photos directly to my email. I can get mail at both at2397@att.com and ray_tay@pacbell.net

Thanks,
Andy

[Andy_Napco]

Any success with the pictures? Just always eager to work on my truck.

Thanks,
Andy

[Giladad1]

I'm interested in your parts or what would be left of them. Mark in AZ Giladad1@aol.com

[1956cameo]

Sorry guys. Getting settled into a new job and getting my house ready to sell. I keep forgetting about the car stuff. I will try to get some pictures on the board tomorrow.

[Andy_Napco]

No problem. I'm happy to forego the pictures and buy the linkage setup from you as I described. Would also be interested in the small metal tube vacuum line from the distributor to the carb, the road draft tube and its clamps, one at the head and one at the tranny pan. Would also like to buy the two valve cover breather caps. Would $150 for the lot be reasonable?

Andy

[1956cameo]

Andy, I guess I must be missing something because I dont have anything that came off of the valve covers. I would really like to sell all the parts as a whole, but if the two of you need different parts and can buy most or all of the parts I could possibly split everything up. However if someone is interested in all the parts as a whole I would like to sell the lot whole versus splitting it up.

Anyways here are some pictures. I don't have a picture of the transmission itself because we are moving and it is in storage; however if someone wants me to I can get a picture of it as well. I also have the steering column with the shifter and some linkage in storage. I will try to take pictures of both items and post them as well.

Here are the basic parts, flywheel, flywheel housing,trans cross member, and trans fluid filler tube (note the filler tube is cracked on bottom and will need work).


Mounts holding the front of the transmission into place.


Bracket that went on the interior portion of the firewall, and a piece of linkage that came off the transmission itself.

[1956cameo]

The linkage bracket that bolted to the rear of the engine with the transmission linkage.


Another picture of the linkage.


The original carburator with linkage on it that connected to the transmission.

[Andy_Napco]

Pictures look great, I'd like to buy eveything you have shown. If you had the small tube that ran from the carb to the distributor that would be awesome. Do you have the 6 bolts that held the flywheel to the end of the crank? Would $200 plus shipping be enough? Let me know.

Thanks,
Andy

[Giladad1]

I'll give you $100 for the cross-member. Mark in AZ

[1956cameo]

I might have someone interested in the whole lot, but I wont know if they can use if for sure until the end of the week. If they don't buy everything then I will consider breaking the parts up.

Andy-Napco, I remember the tube bieng there, but I am not finding it. I will have to look thru my parts bin in storage to know for sure. As far as the flywheel bolts I have 5 of the 6. Unfortunately one was frozen in place and had to ground off.

Giladad 1, That would seem like a reasonable price. If I part the lot up I will price everything as individual pieces so I comply with the forum rules.

[Andy_Napco]

Are the linkage parts available I was interested in available? Curious as I've been looking for these parts for a long time and would hate to start looking again.

Thx,
Andy T.

[Andy_Napco]

Afternoon,

Did you sell the engine/tranny complete? Would still like to buy the linkage parts.



Andy

[1956cameo]

Hey Andy, The person that wanted the entire set up ended up not bieng able to get the GMC due to excessive rust damage. As much as I would really like to help a fellow member get much needed parts, I think it would be best that I try and continue to sell/trade all of these parts as a whole.

[Andy_Napco]

Understandable.

Would you be amenable to letting me pay you to borrow them for a short while to get copies made?

Andy

[Andy_Napco]

Would you be willing to sell the tranny and linkages together?. I could use an extra tranny as part can be hard to come by and I'd be willing to pay a fair price.

Andy

[1956cameo]

I guess you could let me know exactly what parts/linkages you would want with the transmission and we could go from there. Maybe Gildad1 would still be interested in the cross member. If I can get close enough to what I am looking for (price wise) I might break the parts up.

[Giladad1]

Yep, still interested in the cross-member AND the bellhousing. Mark in AZ

[Andy_Napco]

Where abouts in Oklahoma are you so I can get some shipping
quotes on shipping the tranny? I can make you an offer combined
with what Giladad1 is offering

Thx,
Andy
Posted via Mobile Device