Ordered my Pro Filer heads today

[POPO1984]

I finally ordered my heads today. They should be here in a week or so.

195cc intake runner
65cc chamber
1.60 ex
2.02 in

[shawnt]

Who did you order from? There has been a lot of delay in them being shipped lately. They make damn good power though! What's the specs on the motor? Congrats!
Shawn
Posted via Mobile Device

[POPO1984]

I got them through Speier racing heads.

383
Bullet hyd. roller 228/234 .530
rpm air gap
670 avenger

[ripdog28]

I would contact someone about the cam. It looks a bit small for those unless you just want a cruiser. itll still make good power but those heads can use some more lift and probably a little more duration.

[POPO1984]

Yeah i know it is small but it is just a cruiser for now. I will upgrade the cam later if I want to get more out of it. Right now it should be over 450 hp/tq which is what im looking for.

[shawnt]

Chad speier is who is fastest. He knows his stuff!
Posted via Mobile Device

[POPO1984]

Yeah I talked to him the other day and he is debating if we should go with 2.02 or 2.05 valves. He was a real easy person to talk to and pretty cool too

[regan wilson]

Originally Posted by POPO1984

I finally ordered my heads today. They should be here in a week or so.

195cc intake runner
65cc chamber
1.60 ex
2.02 in

While you are at it can you go ahead and order me some 12 degree Profilers with some 2.52 intake valves ? Since you got the hookup . lol ...Hope theywork good for ya .

[POPO1984]

Ill get right on it. I hope they work good too I've been doin alot of **** talking
Posted via Mobile Device

[POPO1984]

They finally came in today. Sorry didnt get the port job will post pics soon

[POPO1984]

Pics

[POPO1984]

Pics 2

[POPO1984]

Pics 3

[CaptMadDog]

any progress / have it running yet? was looking to get a set. were these chads econo port? thanks

[Camaro_nut2001]

Originally Posted by POPO1984

Pics 3

Those look GREAT!!! Are you gonna open the intake runners up a little? Are you runnin a flat top piston? What size cam are you gonna run?

[POPO1984]

These are bone stock. I wish I would have got the econo port job but oh well. The engine is gonna have dished piston 9.8:1 Cr with a 228/234 hydraulic roller cam

[stich626]

where are they made

[POPO1984]

Ohio USA

[CaptMadDog]

well keep us posted on how it runs! im going to be in the market for heads soon and im looking at those or a set of brodix track 1's.

[Camaro_nut2001]

Originally Posted by POPO1984

These are bone stock. I wish I would have got the econo port job but oh well. The engine is gonna have dished piston 9.8:1 Cr with a 228/234 hydraulic roller cam

They should make some pretty good power & it's GREAT they're made in the USA. What's the lift & lobe sep. on that cam? What gear are you runnin? I'm interested to see how these heads do.

[POPO1984]

Got some work done on the engine monday and tuesday. Im getting more and more excited by the day

[POPO1984]

Almost done just need to bolt up the water pump, distributor, and carb. Sad thing is it will probably be 6 months before I get to crank it up. On a side not we primed it up today and it showed 60 psi steady while just priming it.

Im gonna be running a serpintine belt set up so i got to get it on too.

[POPO1984]

Well got her running today. Sounded nice with open headers. I will replace these with the new Hedmans after a few heat cycles and some tuning. Here is a crappy cell cam video. There is some water seeping from the studs so I guess we will take them out one at a time and put more thread sealer and then add the gm pellet to seal it all up. I guess youll have to log into facebook to see the video. Ill have to fix that later for you guys without facebook

http://www.facebook.com/video/video....21814947&saved

[OrangeCrush1970]

Wanted to check in and see how the profiler heads have treated you over the last few years? I am in the market and have been researching their sbc line....look like yours were pretty nice out of the box?

[POPO1984]

Well. I just ran it the initial 20 or so minutes and sealed up the studs a few days later and ran it for another 20 or so minutes. Since then it has not been ran. I will hopefully get it on the road in the next month or two. I have had to kids since then so Family has taken a lot of my time. I will post a vid of the start up and running it around as soon as I get it going. I have complete exhaust on it now and installed a new painless harness. Just waiting on a few small parts. On a side not don't use the reverse water pump from skip white. My mounting flange came of while turning the engine over and chewed up my Copper radiator. The would not help with the radiator or even refund my money for the water pump. I now have a edelbrock.