Vibration Damper. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

MSL · 03-30-2003, 01:46 AM

Ok this has been on my mind for awhile and i have to ask but my Vibration damper or harmonic balancer. Well it wobbles a little i had noticed it when i timed my engine. What kind of problems will i have with this going on. and what do you recommend doing to fix it.

Prerunner1982 · 03-30-2003, 01:58 AM

i would buy a new one.. mine does this as well and i think my crank pulley is bent.. when i build an engine for it i will replace with a better one...

MSL · 03-30-2003, 02:20 AM

I will buy a new one but if i remeber right i heard it has to be balanced to match the crankshaft. which if this is true i will have to pull my engine. I hope some more of you guys can help me out on this.

Mike76251 · 03-30-2003, 03:29 AM

Have a look at the rubber ring between the inner and outer half of the damper and make sure it is not trying to seperate.

My Z/28's came apart and it took out the timing cover.

Also, if you buy a decent one like say a Fluidamper or any any SFI approved one then it will be balanced quite well from the factory.
There will be no need to balance it with the crank.

Those Fluidampers are high but well worth it.
They make your crank bearings last much longer as they are tuned over a wider range than factory type ones.

A damper that has a wobble in it will ruin those bearings pretty fast as they put loads on them that they are not designed to handle.

MSL · 03-30-2003, 03:39 AM

Ok i will have to check that out. Also could that balancer wobbling like that make my engine feel like its missing or just running poorly at a idle i have also noticed when driving it the motor i guess shacks a little. also where would be a good place to look up those balancers.

Mike76251 · 03-30-2003, 03:45 AM

Quote:

Originally posted by MSL
Ok i will have to check that out. Also could that balancer wobbling like that make my engine feel like its missing or just running poorly at a idle i have also noticed when driving it the motor i guess shacks a little. also where would be a good place to look up those balancers.

It is hard to say if that could cause a percieved miss. I don't really think so because if it was off that much I think it would be going through the hood by then.

Jegs or Summit would be a good place to get them. They both have decent prices on them.
Fliudampers web site has a good FAQ you might want to try.

MSL · 03-30-2003, 03:51 AM

Ok thanks, also do you have a link to Fluidampers appreciate it.

Mike76251 · 03-30-2003, 04:08 AM

It is Fluidamper.com but I can't get it to come up right now.

MSL · 03-30-2003, 04:12 AM

I found it dang those are spendy too.

Dang what was the SFI i might have to get that for now.

MSL · 03-30-2003, 04:45 PM

Anyone else have this problem and what did you do.?

03-30-2003, 01:46 AM	#1
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	Vibration Damper. Ok this has been on my mind for awhile and i have to ask but my Vibration damper or harmonic balancer. Well it wobbles a little i had noticed it when i timed my engine. What kind of problems will i have with this going on. and what do you recommend doing to fix it.

03-30-2003, 01:58 AM	#2
Prerunner1982 Registered User Join Date: Oct 2002 Location: Edmond, OK Posts: 5,904	i would buy a new one.. mine does this as well and i think my crank pulley is bent.. when i build an engine for it i will replace with a better one... __________________ Jon 1982 Chevy Silverado 350/th350.... RETIRED 1993 Jeep XJ 2 door(Cherokee) 4wd 4.0ltr/AX-15 (5spd)/NP231 .... Oklahoma Roll Call

03-30-2003, 02:20 AM	#3
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	I will buy a new one but if i remeber right i heard it has to be balanced to match the crankshaft. which if this is true i will have to pull my engine. I hope some more of you guys can help me out on this.

03-30-2003, 03:29 AM	#4
Mike76251 Senior Member Join Date: Mar 2003 Posts: 2,499	Have a look at the rubber ring between the inner and outer half of the damper and make sure it is not trying to seperate. My Z/28's came apart and it took out the timing cover. Also, if you buy a decent one like say a Fluidamper or any any SFI approved one then it will be balanced quite well from the factory. There will be no need to balance it with the crank. Those Fluidampers are high but well worth it. They make your crank bearings last much longer as they are tuned over a wider range than factory type ones. A damper that has a wobble in it will ruin those bearings pretty fast as they put loads on them that they are not designed to handle.

03-30-2003, 03:39 AM	#5
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	Ok i will have to check that out. Also could that balancer wobbling like that make my engine feel like its missing or just running poorly at a idle i have also noticed when driving it the motor i guess shacks a little. also where would be a good place to look up those balancers.

03-30-2003, 03:51 AM	#7
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	Ok thanks, also do you have a link to Fluidampers appreciate it.

03-30-2003, 04:08 AM	#8
Mike76251 Senior Member Join Date: Mar 2003 Posts: 2,499	It is Fluidamper.com but I can't get it to come up right now.

03-30-2003, 04:12 AM	#9
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	I found it dang those are spendy too. Dang what was the SFI i might have to get that for now.

03-30-2003, 04:45 PM	#10
MSL Registered User Join Date: Mar 2003 Location: So.Oregon Posts: 765	Anyone else have this problem and what did you do.?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.