Toolbox Door Gasket - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Steve Hafner · 07-31-2011, 02:58 PM

I know that the toolbox door gaskets are not reproduced but has anyone found a good source that can be used as one ? There must be a small rubber gasket that would work that NOW comes glued on to something else that I'm not thinking of. The picture below, shows where it goes on the door and this one is in MUCH better shape then mine. I also need the support bracket that keeps the door from going all of the way down. Does anyone have any ideas ?

Thanks !!!

cdowns · 07-31-2011, 03:41 PM

i'd start by lookin in lowes home depot type places at the weaterstipping department// theres all sorts of rubber gasket material stuff there
boat suppliers have good stuff too

Sillyoldman · 07-31-2011, 04:06 PM

I have some trunk seal left over from my buick. I'll check it out and let you know. Don't just run out and buy open cel foam tape, youll be wasting your time.

Pop's C-10 · 07-31-2011, 05:52 PM

http://cgi.ebay.com/ebaymotors/157-W...Q5fAccessories

71 super · 07-31-2011, 06:37 PM

Steve is the gasket round? If it is try the seals that are sold to go underneath door panels. It glues to the door and acts as a seal between door and the panel. They come in pairs for around $10 or less, it will prob. take splicing to get compl,etely around the door.

**LockDoc** · 07-31-2011, 06:41 PM

-
I don't know if the '67-'72 door panel seals would work or not. You should be able to get them from any vendor.

LockDoc

Steve Hafner · 07-31-2011, 07:04 PM

Thanks a lot guys, for your input - I decided to look around Truck Carlisle next Saturday and see what I can find from the "weatherstrip and seal venders" there. If I don't find what I want, I'll go looking for some of the things suggested here. I don't know exactly what it looks like - I haven't seen the toolbox area for over two years and I don't live close to where it is being restored. The guy doing the work is going to bring a hunk of it with him next Saturday. I started this thread in hopes of finding someone who has put some weatherstripping of some kind on their OWN toolbox door. I was thinking I'd like to get some of the material that's a little larger then "factory" so when the door is shut, the black rubber would squeeze up into the crack to make the door stand out a little better against my white truck - I've probably got $500 invested in the restoration of the toolbox area and I want EVERYBODY to notice it !!!

Steve Hafner · 09-23-2011, 11:14 AM

. . . .

As seen in the picture below, my toolbox is now finished ( except for the gasket on the door )

My door never had a gasket while I've owned it, so I don't know what it should look like.

Does anybody have a "hunk" of original toolbox door gasket that they could take a close-up picture of, so I would know what to look for ?

THANKS !!!

. . . .

Steve Hafner · 09-24-2011, 06:59 AM

Ttt

07-31-2011, 02:58 PM	#1
Steve Hafner Registered User Join Date: Sep 2010 Location: Northport, Alabama Posts: 1,353	Toolbox Door Gasket I know that the toolbox door gaskets are not reproduced but has anyone found a good source that can be used as one ? There must be a small rubber gasket that would work that NOW comes glued on to something else that I'm not thinking of. The picture below, shows where it goes on the door and this one is in MUCH better shape then mine. I also need the support bracket that keeps the door from going all of the way down. Does anyone have any ideas ? Thanks !!! Attached Images __________________ . . . . Life is short . . . we only have, right now. . . . . My 70 C-10's BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=475526

07-31-2011, 03:41 PM	#2
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Toolbox Door Gasket i'd start by lookin in lowes home depot type places at the weaterstipping department// theres all sorts of rubber gasket material stuff there boat suppliers have good stuff too __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

07-31-2011, 04:06 PM	#3
Sillyoldman #16876 Join Date: Apr 2005 Location: Auburn WA Posts: 12,266	Re: Toolbox Door Gasket I have some trunk seal left over from my buick. I'll check it out and let you know. Don't just run out and buy open cel foam tape, youll be wasting your time. __________________ Posted via Stationary Device '71 Custom Deluxe C-20 402. '67 Buick Special 455. '49 Plymouth Special Deluxe. *"I love that old car smell"* *Some people are like Slinkies... not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs.*

07-31-2011, 05:52 PM	#4
Pop's C-10 Registered User Join Date: Jul 2010 Location: memphis Posts: 2,537	Re: Toolbox Door Gasket http://cgi.ebay.com/ebaymotors/157-W...Q5fAccessories __________________ 1981 C-10 (Pop's) 1978 Camaro 2006 Lacrosse

07-31-2011, 06:37 PM	#5
71 super Registered User Join Date: Sep 2005 Location: Canton North carolina Posts: 3,080	Re: Toolbox Door Gasket Steve is the gasket round? If it is try the seals that are sold to go underneath door panels. It glues to the door and acts as a seal between door and the panel. They come in pairs for around $10 or less, it will prob. take splicing to get compl,etely around the door. __________________ 67 blue step side- bb 68 gold and white swb cst anniversary 68 custom swb hot rod Ls swap 69 swb cst 6 cylinder/ overdrive 69 black/black cst bb swb 70 orange and white cst Canada built truck swb bb 71 black and white super swb bb 71 red and white super swb 72 green and white super swb 4x4 62 nova wagon 400 series Ls swapped 68 Camaro 327/4 speed- 1 owner, original paint 66 Volkswagen bettle 69 auto stick Volkswagen Beetle

07-31-2011, 06:41 PM	#6
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,769	Re: Toolbox Door Gasket - I don't know if the '67-'72 door panel seals would work or not. You should be able to get them from any vendor. LockDoc Attached Images __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

07-31-2011, 07:04 PM	#7
Steve Hafner Registered User Join Date: Sep 2010 Location: Northport, Alabama Posts: 1,353	Re: Toolbox Door Gasket Thanks a lot guys, for your input - I decided to look around Truck Carlisle next Saturday and see what I can find from the "weatherstrip and seal venders" there. If I don't find what I want, I'll go looking for some of the things suggested here. I don't know exactly what it looks like - I haven't seen the toolbox area for over two years and I don't live close to where it is being restored. The guy doing the work is going to bring a hunk of it with him next Saturday. I started this thread in hopes of finding someone who has put some weatherstripping of some kind on their OWN toolbox door. I was thinking I'd like to get some of the material that's a little larger then "factory" so when the door is shut, the black rubber would squeeze up into the crack to make the door stand out a little better against my white truck - I've probably got $500 invested in the restoration of the toolbox area and I want EVERYBODY to notice it !!! __________________ . . . . Life is short . . . we only have, right now. . . . . My 70 C-10's BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=475526

09-23-2011, 11:14 AM	#8
Steve Hafner Registered User Join Date: Sep 2010 Location: Northport, Alabama Posts: 1,353	Re: Toolbox Door Gasket . . . . As seen in the picture below, my toolbox is now finished ( except for the gasket on the door ) My door never had a gasket while I've owned it, so I don't know what it should look like. Does anybody have a "hunk" of original toolbox door gasket that they could take a close-up picture of, so I would know what to look for ? THANKS !!! . . . . Attached Images __________________ . . . . Life is short . . . we only have, right now. . . . . My 70 C-10's BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=475526

09-24-2011, 06:59 AM	#9
Steve Hafner Registered User Join Date: Sep 2010 Location: Northport, Alabama Posts: 1,353	Re: Toolbox Door Gasket Ttt __________________ . . . . Life is short . . . we only have, right now. . . . . My 70 C-10's BUILD THREAD: http://67-72chevytrucks.com/vboard/s...d.php?t=475526



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.