|
11-14-2011, 04:59 PM
|
#1 |
|
Registered User
Join Date: Oct 2011
Location: Normal, IL
Posts: 82
|
Width of rim
I have 15" rally wheels on my truck, trying to find width of them.
__________________
1972 C10 SHORT BED, BLACK ON BLACK, ZZ3 CRATE MOTOR WITH B&M 250 SUPERCHARGER, HEADERS, 350TURBO TRANS, BOOST RETARD, POSI, 373 GEARS 1966 MUSTANG COUPLE, 289 HIPO MOTOR, CAM, 650 HOLLEY CARB, FULL LENGTH HEADERS, 2.5" FLOWMASTER EXHAUST, HURST SHIFTER, 373 GEARS POSI 2006 MONTE CARLO, FLOWMASTER MUFFLERS, K&N INTAKE, EXTERIOR MODS |
|
|
|
11-14-2011, 06:37 PM
|
#2 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Width of rim
most accurate way is to take a tire off the rim and measure with a ruler
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
11-15-2011, 07:24 PM
|
#3 |
|
Junior Member
Join Date: Jul 2002
Location: Scottsdale, AZ
Posts: 1,701
|
Re: Width of rim
Blown,
GM made 15" truck ralleys in very few standard widths. 6 lugs are most often 8" wide and 5 lugs could be 7" or 8". I see you have a 72 so guessing you have 5 luggers. Unless you have later model faux ralleys that are just a plain steel wheel, we should be able to figure this out without taking the tire off. Post a pic taken from an angle to the wheel, not square on, and I'll bet we can tell you just by looking. Also, backspacing would be different. You can measure that without taking the tire off. I have a set but I don't recall now what the measurement is. I'm sure someone will chime in with that.
__________________
"I was patina when patina wasn't cool." 1973 Cheyenne SWB Sunset Gold / Frost White / Saddle |
|
|
|
|
11-15-2011, 09:33 PM
|
#4 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,064
|
Re: Width of rim
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
|
11-15-2011, 11:28 PM
|
#5 |
|
Registered User
Join Date: Aug 2010
Location: Edwards, CA
Posts: 7,503
|
Re: Width of rim
Pop over to a tire shop. They should have a big plastic rim caliper for their balance machine.
__________________
Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID ** Blazer SPID ** Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders ** Do you have a 1972 Plaid Pickup? ** Plaid Blazer ** Plaid Suburban |
|
|
|
|
11-16-2011, 12:44 AM
|
#6 |
|
20' Daredevil (Ret)
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,722
|
Re: Width of rim
Some wheels have their dimensions stamped on the back side...
And if measuring, measure inside bead-to-bead. Only mentioned b/c I have seen some folks measure outside, or total width of the rim. 
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
|
|
|
|
11-16-2011, 01:41 AM
|
#7 |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,031
|
Re: Width of rim
Every 5 lug rallye wheel I have ever owned has the size stamped on the inside...might need to clean it up a bit to see.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
