What did you get done 2/12/12 valentines edition - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**old Rusty C10** · 02-12-2012, 08:29 PM

still making progress on body and paint.. converted my insurance to collecters insurance.. other than that nothing really.. how about you all?

Jonboy · 02-12-2012, 08:49 PM

We got back from Cancun late last night, so nothing truck related at all.

Goldfinger · 02-12-2012, 09:01 PM

celebrated the anniversary of my truck by repainting it.

Kerlijah · 02-12-2012, 09:04 PM

Didnt get anything done on my truck, but I helped my buddy tear apart his new (to him) '80 swb 4x4. We'll be doing a frame off resto on it, nothin fancy, just building a good daily driver/work truck. Plans so far include a 4" lift, 33" mudders with 18s, bad@ss sbc/700r4, etc....tryin to get it done by June, cant wait!!

Worked on it for 3 or 4 hours last night, got quite a bit done I think! Stripped it down to just the chassis and cab, completely gutted the interior, ended up with a gigantic pile of scrap metal, lol

ocbaud · 02-12-2012, 09:20 PM

Got my truck sold...

riz · 02-12-2012, 09:50 PM

Eric,

I thought you sold it a while ago???

RIZ

SCOTI · 02-12-2012, 09:55 PM

Some parts came in that were needed for the upgrades that I'm doing for the dually. I got a heated o2 sensor & a custom calibrated chip for my motors/drivetrains specs from Harris Performance.

With those parts now in hand, I needed to source some mounting hardware for the heated o2 sensor upgrade. Not wanting to pay more for shipping/handling than what an actual o2 mounting bung would cost, I sourced some spark plug anti-fouler fittings I could pick up locally to use instead. After a little 'hacking' for use in a different application, I got them welded into the header collectors & chased the threads to ensure proper tension. Today, I test fit the header w/the o2 sensor installed to 100% verify clearance & then got the computer chips swapped around. While outside, I also tweaked the req'd mounting hardware for the pwr-steering pump conversion (I had to cut 4 longer M10x1.5 thread bolts down to 2 different correct sizes).

While validating the final pwr-steering pump mounting fit, I decided the current accessory bracket coating was not acceptable as it's already flaking off in multiple areas (MarHyde etching primer & gloss black rattle can). So, the brackets were pulled off the motor & are heading to the coaters w/the headers this week.

1 step forward, 2 steps back..... for @ least a week

.

Mr. 250r · 02-12-2012, 10:05 PM

slowly finishing the 6.0 swap

tidos76 · 02-12-2012, 11:31 PM

Finished up wrapping my dash and installing the door pads. ran the 1/0 wire through the firewall,removed all the stereo and amps. just have 1 more seat to take out and sub box. replace carpet, wrap speaker box, remake console, and reinstall EVERYTHING....lol and a lil over a month to do it all.

sethv · 02-12-2012, 11:36 PM

Got my first K10 back

Did some work to her today:
Replaced the fuel filters, and reinstalled all my audio equipment. Didn't turn out too bad I think

Gotta clean the wiring up a lot, but it all works so I'm happy

85burb · 02-13-2012, 12:30 AM

Not a hole lot done this week end but got new tires for wifes truck wends. Installed them and sold the wheels we had on it. Went to junkyard and got ac box for her truck. Only action the burb seen was taking old wheels to buyer. And wife cleaned the blue junk off of the white letters on her new tires.

54Caddy · 02-13-2012, 12:46 AM

Quote:

Originally Posted by tidos76

Finished up wrapping my dash and installing the door pads. ran the 1/0 wire through the firewall,removed all the stereo and amps. just have 1 more seat to take out and sub box. replace carpet, wrap speaker box, remake console, and reinstall EVERYTHING....lol and a lil over a month to do it all.

What material did you use on the dash??

tidos76 · 02-13-2012, 12:52 AM

Its all vinyl except for around the door handle and below the armrest, which is suede.

flamingbig10 · 02-13-2012, 01:31 AM

friday worked on mounting the wiper motor under dash but it decided to lock up on me its been kind of finicky since I've owned the truck I believe its original motor so went picked up a reman 85-87 unit since they look much cleaner without the washer pump on them but that fare as I got
Saturday I had to work all day I thought I had this problem vehicle figured all out thats been kicking my but all week but no such luck, with my frustration I spent the rest of the day watching tv
Today I went to the Dallas boat show with my old man lots of nice boats but even nicer scenery

when I got home I worked of my yjs driver side window hasn't rolled up correctly since I had to break in two it a couple weeks ago when I locked the keys in it it usually I don't even lock the doors but for som reason I did that night. The window would stop 1/8" before it went in side the top of the door, then all a sudden it wouldn't roll up or down at all took the regulator out it was all bent to heck and 25 year old grease was gunk up straighten the regulator in the big vise and cleaned the gunk out with some bc added some new lube installed it back in door work better than new

JRANGER · 02-13-2012, 02:17 AM

nothing...It was cold as crap this weekend and I have garage so I worked on my website and cleaned my house

Stepper86 · 02-13-2012, 03:20 AM

Cut my exhaust and re-routed it to go over the transmission crossmember on passenger side, after that was done I went home and painted walls.

*mrhino* · 02-13-2012, 06:51 AM

i got my other seat installed and center console.

D13 · 02-13-2012, 07:32 AM

Started making a sleeve puller for my Allis so I can get the motor rebuilt and get it out of the way of the truck projects. Didn't have correct thickness and size pf plate so welded some together (good practice), lathed one side smooth (good practice), then this week cut out the pulling plate and make the hole in the support plate to size. Can't wait to get it done so I can work on the truck.

jitteryguy · 02-13-2012, 10:10 AM

spent all day saturday and most of sunday get'n the water unfroze for the shower unit,,,,,,,,,,,,,,,,,,,then it froze again last night ,,,,,,,,,,,,,,dang it.

rfmaster · 02-13-2012, 11:39 AM

Took advantage of nice weather and the fact that I have mornings free to myself! (aka kitchen pass)

Saturday scored bunch of parts from a local pick JY (50% off sale) - couple of alternators, throttle cable, smog diverter valve (just because I live in eco-stupid CA), sensors, relays galore for various projects.

Sunday walked the LBC Vet memorial car swap - several very nicely Sq-bodies in the coral. Sorry no quality photos this time. Got some tools and shop supplies.

Put some miles on a new engine, which is slowly is breaking in.

//RF

bigblock73 · 02-13-2012, 01:40 PM

Goy my 1-piece windows installed finally. Also finished up my remote on/off switch custom installation...pics to follow soon.

Fixwhataintbroke · 02-14-2012, 03:41 PM

Got around to wiring in relays for the headlights. MAN what a difference!

GuZ · 02-14-2012, 04:48 PM

Nothing new as of late.........had to do some work to the motor in the Wife's DD (Grand Cherokee plenum pan repair). That was fun.

Hopefully crackin back into the truck in a week or so!!

DBLSPRT68 · 02-14-2012, 09:30 PM

Getting ready to move to Charlotte, NC. Sold my 89 Suburban today! Hated to see her go, but can't take with me either...... I will sell my 83 C20 to the same guy, he said he would take it also!! Got to use it for another week. I'm takeing my 85 extended cab with me

NCTyphoonKid · 02-14-2012, 09:38 PM

Quote:

Originally Posted by DBLSPRT68

Getting ready to move to Charlotte, NC. Sold my 89 Suburban today! Hated to see her go, but can't take with me either...... I will sell my 83 C20 to the same guy, he said he would take it also!! Got to use it for another week. I'm takeing my 85 extended cab with me

I'm about 45 mins for Charlotte so I ain't gonna be too far from ya.

02-12-2012, 08:29 PM	#1
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,313	What did you get done 2/12/12 valentines edition still making progress on body and paint.. converted my insurance to collecters insurance.. other than that nothing really.. how about you all? __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

02-12-2012, 08:49 PM	#2
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: What did you get done 2/12/12 valentines edition We got back from Cancun late last night, so nothing truck related at all. __________________ 1974 Jimmy- 5.3/4L80e/NP241

02-12-2012, 09:01 PM	#3
Goldfinger Registered User Join Date: May 2010 Location: laurel hill Fl Posts: 645	Re: What did you get done 2/12/12 valentines edition celebrated the anniversary of my truck by repainting it. __________________ 1985 C10 Custom Deluxe LWB 305/700r4 [ Goldfinger ] 1999 k3500 crew cab dually 6.5tdi/4l80e

02-12-2012, 09:04 PM	#4
Kerlijah Registered User Join Date: Feb 2011 Location: Boise, ID Posts: 293	Re: What did you get done 2/12/12 valentines edition Didnt get anything done on my truck, but I helped my buddy tear apart his new (to him) '80 swb 4x4. We'll be doing a frame off resto on it, nothin fancy, just building a good daily driver/work truck. Plans so far include a 4" lift, 33" mudders with 18s, bad@ss sbc/700r4, etc....tryin to get it done by June, cant wait!! Worked on it for 3 or 4 hours last night, got quite a bit done I think! Stripped it down to just the chassis and cab, completely gutted the interior, ended up with a gigantic pile of scrap metal, lol Attached Images __________________ ~Wooden Indian~ 1979 C10 SWB, shaved bed rails, drip rails, tailgate handle. 350 w/ Comp cam, hydraulic lifters, Edelbrock Performer intake, Edelbrock 650 carb, Flowtech headers, Flowmaster 40s, turbo 350 w/stage 2 shift kit...so much fun!

02-12-2012, 09:20 PM	#5
ocbaud Garage Queen Material Join Date: Oct 2002 Location: USA Posts: 4,129	Re: What did you get done 2/12/12 valentines edition Got my truck sold...

02-12-2012, 09:50 PM	#6
riz Registered User Join Date: Oct 2011 Location: hudson,wi Posts: 805	Re: What did you get done 2/12/12 valentines edition Eric, I thought you sold it a while ago??? RIZ

02-12-2012, 09:55 PM	#7
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,071	Re: What did you get done 2/12/12 valentines edition Some parts came in that were needed for the upgrades that I'm doing for the dually. I got a heated o2 sensor & a custom calibrated chip for my motors/drivetrains specs from Harris Performance. With those parts now in hand, I needed to source some mounting hardware for the heated o2 sensor upgrade. Not wanting to pay more for shipping/handling than what an actual o2 mounting bung would cost, I sourced some spark plug anti-fouler fittings I could pick up locally to use instead. After a little 'hacking' for use in a different application, I got them welded into the header collectors & chased the threads to ensure proper tension. Today, I test fit the header w/the o2 sensor installed to 100% verify clearance & then got the computer chips swapped around. While outside, I also tweaked the req'd mounting hardware for the pwr-steering pump conversion (I had to cut 4 longer M10x1.5 thread bolts down to 2 different correct sizes). While validating the final pwr-steering pump mounting fit, I decided the current accessory bracket coating was not acceptable as it's already flaking off in multiple areas (MarHyde etching primer & gloss black rattle can). So, the brackets were pulled off the motor & are heading to the coaters w/the headers this week. 1 step forward, 2 steps back..... for @ least a week . __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-12-2012, 10:05 PM	#8
Mr. 250r Registered User Join Date: Dec 2010 Location: freeburg, illinois Posts: 885	Re: What did you get done 2/12/12 valentines edition slowly finishing the 6.0 swap Attached Images __________________ 1987 Chevy V30 - http://67-72chevytrucks.com/vboard/s...d.php?t=573854 1988 IROC-Z Camaro - 305/T5 T-Top 1989 GMC V35 - Marbolo Express http://67-72chevytrucks.com/vboard/s...d.php?t=596850 1991 V2500 Suburban Silverado - Sold 1991 V2500 Suburban Scottsdale - Big Nasty http://67-72chevytrucks.com/vboard/s...d.php?t=497423 2001 Ram 3500 5.9 H.O NV56 EC DRW - Sold 2003 1500 Silverado 2004 Ram 3500 5.9 H.O NV56 CC DRW - Sold 2005 Silverado 2500HD 6.6/ZF6 CC LWB

02-12-2012, 11:31 PM	#9
tidos76 Registered User Join Date: Sep 2011 Location: oklahoma city Posts: 33	Re: What did you get done 2/12/12 valentines edition Finished up wrapping my dash and installing the door pads. ran the 1/0 wire through the firewall,removed all the stereo and amps. just have 1 more seat to take out and sub box. replace carpet, wrap speaker box, remake console, and reinstall EVERYTHING....lol and a lil over a month to do it all.

02-12-2012, 11:36 PM	#10
sethv Registered User Join Date: May 2011 Location: Bradford, PA Posts: 395	Re: What did you get done 2/12/12 valentines edition Got my first K10 back Did some work to her today: Replaced the fuel filters, and reinstalled all my audio equipment. Didn't turn out too bad I think Gotta clean the wiring up a lot, but it all works so I'm happy Attached Images __________________ 1981 K10 Scottsdale 305 ci \| TH350 \| NP208 \| 60k miles

02-13-2012, 12:30 AM	#11
85burb Registered User Join Date: Dec 2009 Location: lindale,tx Posts: 2,373	Re: What did you get done 2/12/12 valentines edition Not a hole lot done this week end but got new tires for wifes truck wends. Installed them and sold the wheels we had on it. Went to junkyard and got ac box for her truck. Only action the burb seen was taking old wheels to buyer. And wife cleaned the blue junk off of the white letters on her new tires. Attached Images __________________ 82 c10 5.3/4l60 84 c20 5.3/sm465 85 chevy k10 suburban LQ4/4l60 91 chevy c10 suburban Lsa 5.3/4l60 2017 Silverado whipple 5.3 1964 Vw beetle 1974 vw beetle

02-13-2012, 12:52 AM	#13
tidos76 Registered User Join Date: Sep 2011 Location: oklahoma city Posts: 33	Re: What did you get done 2/12/12 valentines edition Its all vinyl except for around the door handle and below the armrest, which is suede.

02-13-2012, 01:31 AM	#14
flamingbig10 6.0 powered square Join Date: Feb 2008 Location: Mesquite texas Posts: 3,459	Re: What did you get done 2/12/12 valentines edition friday worked on mounting the wiper motor under dash but it decided to lock up on me its been kind of finicky since I've owned the truck I believe its original motor so went picked up a reman 85-87 unit since they look much cleaner without the washer pump on them but that fare as I got Saturday I had to work all day I thought I had this problem vehicle figured all out thats been kicking my but all week but no such luck, with my frustration I spent the rest of the day watching tv Today I went to the Dallas boat show with my old man lots of nice boats but even nicer scenery when I got home I worked of my yjs driver side window hasn't rolled up correctly since I had to break in two it a couple weeks ago when I locked the keys in it it usually I don't even lock the doors but for som reason I did that night. The window would stop 1/8" before it went in side the top of the door, then all a sudden it wouldn't roll up or down at all took the regulator out it was all bent to heck and 25 year old grease was gunk up straighten the regulator in the big vise and cleaned the gunk out with some bc added some new lube installed it back in door work better than new __________________ Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326

02-13-2012, 02:17 AM	#15
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: What did you get done 2/12/12 valentines edition nothing...It was cold as crap this weekend and I have garage so I worked on my website and cleaned my house __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

02-13-2012, 03:20 AM	#16
Stepper86 Registered User Join Date: Sep 2011 Location: Stockholm Posts: 263	Re: What did you get done 2/12/12 valentines edition Cut my exhaust and re-routed it to go over the transmission crossmember on passenger side, after that was done I went home and painted walls. __________________ Tom.______________________________________ The fleet: 2007 BMW 530xi M (daily driver) 1986 C-10 Stepside (project "my time") 1992 Corvette cab (summer time daily driver) 1969 Cadilac DeVille Cab ("it just need some paint")



Register or Log In To remove these advertisements.

02-13-2012, 06:51 AM	#17
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: What did you get done 2/12/12 valentines edition i got my other seat installed and center console.

02-13-2012, 07:32 AM	#18
D13 Registered User Join Date: Feb 2007 Location: Memphis MI Posts: 1,851	Re: What did you get done 2/12/12 valentines edition Started making a sleeve puller for my Allis so I can get the motor rebuilt and get it out of the way of the truck projects. Didn't have correct thickness and size pf plate so welded some together (good practice), lathed one side smooth (good practice), then this week cut out the pulling plate and make the hole in the support plate to size. Can't wait to get it done so I can work on the truck. __________________ 1987 2 ton 1982 250/TH350 beater in progress Dad's 1981 3/4 L6 3 on tree posi and no options, awaiting restoration or scrapping Plus a mess o' tractors

02-13-2012, 10:10 AM	#19
jitteryguy GoatLube Experss Join Date: Oct 2009 Location: clarksville, Tn. Posts: 1,337	Re: What did you get done 2/12/12 valentines edition spent all day saturday and most of sunday get'n the water unfroze for the shower unit,,,,,,,,,,,,,,,,,,,then it froze again last night ,,,,,,,,,,,,,,dang it. __________________ *Goat Lube Express*, locations in Qalat,Afghanistan & Clarksville, Tn. '87 R30 dually 454/TH400 '85 1/2 ton CCSB '92 S10 350/350 '84 MonteCarlo 383/PG/9"ford '78 Malibu wagon 350/350 '78 Cutlass (project family car) '96 S10 Jimmy (Moma's)

02-13-2012, 11:39 AM	#20
rfmaster Registered User Join Date: Oct 2003 Location: OC CA Posts: 1,374	Re: What did you get done 2/12/12 valentines edition Took advantage of nice weather and the fact that I have mornings free to myself! (aka kitchen pass) Saturday scored bunch of parts from a local pick JY (50% off sale) - couple of alternators, throttle cable, smog diverter valve (just because I live in eco-stupid CA), sensors, relays galore for various projects. Sunday walked the LBC Vet memorial car swap - several very nicely Sq-bodies in the coral. Sorry no quality photos this time. Got some tools and shop supplies. Put some miles on a new engine, which is slowly is breaking in. //RF __________________ "The Beast" 1975 Chevrolet C20 longbed 350/700R4! with 3inch body lift Dual Flowmasters Super 40's! TBI retrofit completed (2007-07-29) New 383CID (+030) 08-304-8 9.5:1CR x36,005 (2012-12-17)

02-13-2012, 01:40 PM	#21
bigblock73 yeller Join Date: Oct 2001 Location: Twin Cities Posts: 13,824	Re: What did you get done 2/12/12 valentines edition Goy my 1-piece windows installed finally. Also finished up my remote on/off switch custom installation...pics to follow soon. __________________ Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale

02-14-2012, 03:41 PM	#22
Fixwhataintbroke Enthusiast Join Date: Jun 2010 Location: Graham, Wa. Posts: 192	Re: What did you get done 2/12/12 valentines edition Got around to wiring in relays for the headlights. MAN what a difference! __________________ - Cole 1979 Chevy C30 w/ carb 454. 1992 Chevy K1500 w/ tbi 350. Sold 1997 Dodge Ram 1500 w/ Magnum 360 Sold "Good judgment comes from experience. Experience comes from poor judgment." - George Washington

02-14-2012, 04:48 PM	#23
GuZ Registered User Join Date: Jan 2012 Location: Wenatchee, WA Posts: 36	Re: What did you get done 2/12/12 valentines edition Nothing new as of late.........had to do some work to the motor in the Wife's DD (Grand Cherokee plenum pan repair). That was fun. Hopefully crackin back into the truck in a week or so!!

02-14-2012, 09:30 PM	#24
DBLSPRT68 Registered User Join Date: Nov 2000 Location: Ft. Mill, SC USA Posts: 931	Re: What did you get done 2/12/12 valentines edition Getting ready to move to Charlotte, NC. Sold my 89 Suburban today! Hated to see her go, but can't take with me either...... I will sell my 83 C20 to the same guy, he said he would take it also!! Got to use it for another week. I'm takeing my 85 extended cab with me __________________ PROJECT TRUCK: 1985 SWB C10 Silverado Black/Charcoal, 1990 V2500 Suburban, 2018 Suburban, 2005 GMC 2500HD CCSB, 2014 Toyota Camry SE, HAD.....1968 Camaro RS/SS Family owned since new; 350 3 speed SOLD

Register or Log In To remove these advertisements.