AZ 69 suburban body for parts

[t korinek]

Cutting whats left of this suburban body up, so if you need some piece let me know & I'll price it according to how big & how much trouble to cut off.
I'll be sending it to scrap in 4 days.
3rd door pillar in solid shape, 3rd door rocker also good, area behind 3rd door has some rust holes & both sides behind the wheel well also has rust.
Driver side in front of rear wheel in nice shape & so is 4th door skin.
Thanks,
Tom

[t korinek]

Has a good radio section $30 + ship or whole dash $65 + shipping
Good windshield chrome $30 + shipping
rear side glass $25 each + ship

[Marc33]

I need some roof pieces, and the pass side tailight quarter area(extending back past the side marker). I can email you some outlined pictures tomorrow, cool?

[t korinek]

Both tail light sections have dents $35 each

[t korinek]

Hatch is rusted out, hardware is for sale
Gas tank in good shape with straps, local pick up only $80

[Marc33]

ok, so skip the taillight sections, but I need some roof pieces. above windshield on both sides as well as some other roof pieces.

[Slinger60]

I am interested in both these sections if there good. Thanks Shawn

[t korinek]

Slinger60 the driver side piece in nice shape $45
passenger side piece has some rust holes, see pic $15
mark33 post pics of what pieces of the roof you need & I'll price it all, passenger side tail light section not as bad as the driver side.
Thanks,
Tom

[Slinger60]

Ill take the drivers section. Are the wheel arches any good? Thanks Shawn

[t korinek]

Also have this piece, that is at the rear of the driver side inner fender $25

[t korinek]

Wheel arches are in good shape, I don't have any pics of them till tomorrow.

[richard2717]

How are the driver and passenger front floor pans. Need from the trans hump over to the rocker from fromt floor seam to the front seat hump. Shipping to 21826

Thanks
Richard

[Slinger60]

I don't need that inner pc. on the drivers side I will go ahead and take the passneger side pc that i need also. And I will wait untill i can see some pics of the wheel arches. Thanks Shawn

[richard2717]

I would also be interested in the rear tail light sections as long as they are rust free. Don't care about the dents

Richard

[Slinger60]

Just noticed that the hatch still has the molding on it if it is in good shape I might take that to. Thanks

[D.PASSMORE]

Windshield trim - What kinda shape? Is it the deep lip type?

[richard2717]

I would want the entire section if possible. How bad is the rust in the lower quarters behind the wheels up to about the side marker light area?
Richard

[richard2717]

This is the floor area I am needing on both sides. Hard to see the condition in the picture

[t korinek]

Driver lip has rust near the back, see pic, passenger side is in good shape, no rust, a couple small dings.
No rust in rear passenger tail light section

[71blksuper4x4]

Tom, how much for say the bottom 4 inches of pillar area and the floor below it about 6 inches around it out and to the sides. I can get pics tomorrow. Trevor
Posted via Mobile Device

[t korinek]

Richard, Front floor sections are pretty rough, especially towards the outer edges,probably not good enough for patches in the area your looking at.

[t korinek]

pic of the lower inside rear tail light section & roof

[t korinek]

Passmore, trim in good shape, didn't notice any dings in it, a little scuffing, should polish out, I'm thinking its the deep lip, I'll pull it out to find for sure.

71blksuper4x4 $50 would get that lower pillar & the area around it.
Slinger60 hatch trim in great shape $22

[richard2717]

OK I will pass on floor sections but would like shipping cost for both tail light sections please to 21826

Thanks
Richard

[Slinger60]

Ill take the both pcs. that I posted pics of and rear hatch trim shippped to 96062 PM me Thanks Shawn.