AZ Parting out a 72 shortbed

[t korinek]

This is a 72 non AC truck getting parted out.
SOLD Bed & tail gate $900 SOLD
Cab $400, no major rust , has had quite a few extra holes punched in it SOLD
72 doors $125 each bare SOLD
seat $75 SOLD
Engine $1000 350 with double hump headsSOLD
trans $125 turbo 350 SOLD
Most of the big stuff is pick up only.
Other parts ask & I'll price.
Thanks,
tom

[t korinek]

Here's a few more pics.
disc brake front, 12 bolt leaf spring rear.
frame is bent from cross member forward.

[mrdana60]

Would you ship wheels? And how much for them?

[t korinek]

I'll sell the wheels & tires, the rears are the only pro stars.
$300 for the pair + shipping, tires are old, but have been garaged up until 2 weeks ago.

[mrdana60]

Ok thanks was looking for set of 4. Thanks again. What about the high hump? Any big holes cut?

[t korinek]

Just the hole where the 4 speed used to be & I'm not sure whats under the block of 4x4.

[mrdana60]

How much shipped to 35960

[GMCJOE]

Wish I was state side, I would make a offer on the whole truck minus engine and trans. Damn the luck. Good luck in sales

[t korinek]

$30 shipped for the hump

[mrdana60]

Will take it pending pics when you can.

[ScottH]

Tom, I need a drive shaft. Could u tell me the measurements from u-joints center to center?

Thanks
Scott

[70blackfish]

how much to ship the seat? 93063 so cal.

or any other way to get it to me/

[Littletony]

Can you send me some more pics of the back window? How are the seals?

[blap]

Tom, Interested in the doors.

[chachi127]

If you dont sell the frame as a whole unit I need a couple of pieces. If you're intertested let me know. It would be both sides from front most cross member to the front shock mount. Thanks

[Street Smart]

I need a set of chassis brackets for the motor mounts. Zip codes - 11234
LMK, thanks Charlie

[t korinek]

mrdana60 will get you pics of the hump with the shifter off it.

GMCJOE Thanks

ScottH I'll get you a measurement

70blackfish, shipping this seat even by greyhound would be over a $100

Littletony, will get pics

Blap, will get more pics of the doors

Chachi & StreetSmart, pms sent

[mrdana60]

I shipped a seat and it was 116 I believe thru greyhound. Just trying to help.

[sixty-eight shorty]

In what condition is the engine harness ? If it's good how much do you want for it shipped to azle tx 76020? Thanks , frank
Posted via Mobile Device

[kingsolver72]

What kind of shape and how much for the driver side mirror to 66067?
Posted via Mobile Device

[t korinek]

kingsolver, PM sent
sixty-eight shorty the engine harness is not there

blap, heres a few more pics of the doors, there is no rust, bottoms of doors are nice, passenger side has had some bondo work done on it, there are extra screw holes in the inside where they they did some custom door panels.

littletony, back window is in good shape, seals are shot, I have new ones available though.

ScottH center to center of ujoint is 59 1/2" & has a new ujoint at the rear $75 + shipping if interested

mrdana, sorry, forgot your pic.

[t korinek]

A few more pics
The extra holes in the cab are on the passenger side around the heater core & then I think they used a jack hammer to punch the hole for the antenna, also there's nutserts on the roof & the upper pillars where they must have had a visor on it.
Thanks,
Tom

[mgkgmc]

Is the engine in good shape. I know you cant tell me much without taking it apart. But did they leave any receipts by chance with the engine build?

[t korinek]

I was engine had 500 miles on it, but no receipts, it doesn't look like its ever been ran, it also has a deep sump oil pan on it.

[ScottH]

Tom, DS length looks good, can u LMK what total with shipping would run to 08753?

thanks
Scott