TX WTB Rear Hatch Handle Hardware

[texas04]

Like the title says, I am looking for the hardware (specifically the handle, spring and retaining washer) for the double wall hatch on my 72 Blazer. I am tracking that I can get a replacement handle from Brothers or a hardware store, but the rest of my original assembly rusted into oblivion. I am also open to anybody's ideas on how to replicate the parts on my own. I'm sure plenty of forum members have tackled this before. Thanks.
Posted via Mobile Device

[texas04]

Here is a picture of what I am working with...

[texas04]

Another pic...

[72K5NTX]

I guess I need clarification... do you need the latches and the rods or the metal plate with the square hole the rods attach to? Or do you need the mounting bracket that the whole assembly attaches to inside the top by the bolts that go through the sill of the hatch. I bought the one from Brothers, it is the same one you get at Lowes, just 30 buck higher. I did not have a handle at all and used the one from Lowes.

[texas04]

I found a handle at Home Depot earlier today. Like you said, the same as what Brothers is selling just cheaper. Now what I need is the metal plate with the square hole that the rods attach too, and the spring that wraps around the rod behind the handle. I've got the mounting bracket and the rest of the hardware, it's just all the parts that are on the handle that are shot.
Posted via Mobile Device

[72K5NTX]

I see. I don't have that part. I don't have a spring in mine at all and it works pretty well. It does not spring back like original but the outside latches pull it back straight when closed and latched. As far as the rod attaching plate goes, I think you could make it, the only prob is the square hole. A fabrication/welding /machine shop maybe? Trust me I feel your pain I drove mine with no hatch for about 2 years because of the handle and the hinge mounting plates being roached. I would pull it all out and shoot you some measurements but it would be quite painful for me now that its all together and works well. Somebodies gotta have one apart here that could give you a template though.

[texas04]

No worries, I appreciate the input. Do you have a recommendation for a fabrication/machine shop in Dallas?
Posted via Mobile Device

[Mint68]

Here is what I have in my bag of extra hatch parts, I think I may have some of the metal plate/covers as well . If any of this is what you need let me know. One of the handles was cut off in the plate it goes through, the piece is siezed in there, but would probably come out with some work.

[texas04]

Here is what I have in my bag of extra hatch parts, I think I may have some of the metal plate/covers as well . If any of this is what you need let me know. One of the handles was cut off in the plate it goes through, the piece is siezed in there, but would probably come out with some work.

Mint 68, can you send me a better pic of the circled item? It looks like one of the pieces I need, hard to tell without getting a closer look. Is that the plate with the cut off piece you are referring to?

[Mint68]

try this one, the siezed piece is held to the bracket with a snap ring.

[72K5NTX]

I think there is a pin under the spring that holds the square shaft in there but not positive. Man where were these good ole parts last Summer???

[texas04]

Re: WTB Rear Hatch Handle Hardware
try this one, the siezed piece is held to the bracket with a snap ring.

Mint 68, those are the parts I'm looking for. How much for the parts pictured above shipped to 75229? Thanks.
Posted via Mobile Device
Posted via Mobile Device

[Mint68]

sending pm texas04

[Dale99]

mint, pm sent as I see a part I would like if you dont mind.

[4oldcars]

If anyone else reading this has that same part, I need one. I'm confused where that snap ring came from?

[mgkgmc]

I have a extra set of hatch latch rods that connect the handle to the hatch latches in good shape if your interested.

[LockDoc]

-
I don't know if this will help anyone or not but here is an FAQ I posted about disassembling the handle to get the lock cylinder out.

http://67-72chevytrucks.com/vboard/s...d.php?t=509656

LockDoc

[4oldcars]

I'm still tryin to figure out how to separate the spring and rod bracket from the handle shaft so the handle can be removed from the hatch

[PD1292]

mint68, Would you be so kind as to take a better picture of this part. I think it is almost gone in my hatch. i think i am going to have to attempt to split the top to make a piece like this to replace the missing part. thanks. barry.

[RideSF]

Does any body have a handle for sale refinish able?
Posted via Mobile Device

[sviray]

Originally Posted by Mint68

try this one, the siezed piece is held to the bracket with a snap ring.

Anyone have extra one to sell? Please pm me, thx!

[sviray]

Originally Posted by sviray

Anyone have extra one to sell? Please pm me, thx!

bracket with 2 bolts is what I am looking for...thx in advance!!!

[glenn_grrd@yahoo.com]

Originally Posted by sviray

bracket with 2 bolts is what I am looking for...thx in advance!!!

I need the pivot spring assembly, if anyone has one or a lead to one, please email or pm me.

[1rippen6]

Originally Posted by glenn_grrd@yahoo.com

I need the pivot spring assembly, if anyone has one or a lead to one, please email or pm me.

http://67-72chevytrucks.com/vboard/s...d.php?t=742121

[Jesse B.]

Originally Posted by 1rippen6

http://67-72chevytrucks.com/vboard/s...d.php?t=742121

As 1rippen6 pasted above (thanks!), I have a new latch assembly for sale. Click on his link.