No spark 72 c10 with hei - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**WIDESIDE72** · 04-07-2013, 02:20 PM

A few years ago I installed a skip white hei and a new engine harness from brothers with the hei mod already done in my 350 and it started fine a few times. Then we tore the truck apart for paint. I recently reinstalled everything. Last week I started the truck for the first time after paint and everything worked OK. I drove the truck down to my barn and it was idling while I added trams fluid. It died and would t start. Pulled a plug wire and installed a spark checker inline, no fire. I checked the power wire at the dist, no power. I ran a jumper from the battery to the dist and the truck fired up (?) I am going to pull the harness from the dist block next weekend and check it as I can't figure out why I'm not getting power to the dist with a new harness. I checked and it hasn't gotten pinched, etc that I can see. Does anyone have any ideas?
Posted via Mobile Device

yukon · 04-07-2013, 03:07 PM

Did you check for any blown fuses?

SS Tim · 04-07-2013, 03:16 PM

Try back probing the ignition switch at the connector. Verify power there then work through the circuit.

**WIDESIDE72** · 04-07-2013, 04:36 PM

I was thinking I might have a bad ignition switch. Thanks!
Posted via Mobile Device

**WIDESIDE72** · 04-07-2013, 04:37 PM

Quote:

Originally Posted by yukon

Did you check for any blown fuses?

No fuses on the ignition circuit, to the best of my knowledge.
Posted via Mobile Device

04-07-2013, 02:20 PM	#1
WIDESIDE72 Senior Member Join Date: Aug 2008 Location: Cedar Park, Texas Posts: 7,500	No spark 72 c10 with hei A few years ago I installed a skip white hei and a new engine harness from brothers with the hei mod already done in my 350 and it started fine a few times. Then we tore the truck apart for paint. I recently reinstalled everything. Last week I started the truck for the first time after paint and everything worked OK. I drove the truck down to my barn and it was idling while I added trams fluid. It died and would t start. Pulled a plug wire and installed a spark checker inline, no fire. I checked the power wire at the dist, no power. I ran a jumper from the battery to the dist and the truck fired up (?) I am going to pull the harness from the dist block next weekend and check it as I can't figure out why I'm not getting power to the dist with a new harness. I checked and it hasn't gotten pinched, etc that I can see. Does anyone have any ideas? Posted via Mobile Device

04-07-2013, 03:07 PM	#2
yukon Registered User Join Date: Jun 2011 Location: fairbanks, ak Posts: 26	Re: No spark 72 c10 with hei Did you check for any blown fuses?

04-07-2013, 03:16 PM	#3
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,503	Re: No spark 72 c10 with hei Try back probing the ignition switch at the connector. Verify power there then work through the circuit. Attached Images __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

04-07-2013, 04:36 PM	#4
WIDESIDE72 Senior Member Join Date: Aug 2008 Location: Cedar Park, Texas Posts: 7,500	Re: No spark 72 c10 with hei I was thinking I might have a bad ignition switch. Thanks! Posted via Mobile Device



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.