|
04-10-2013, 01:24 PM
|
#1 |
|
Registered User
Join Date: Feb 2012
Location: turlock
Posts: 2,177
|
Alignment issue
On my 72 my left front wheel tucks in at the top causing me to pull and eat away at the inside of the tire.
I've maxed my limit on the stock studs for the upper a-arm spacing so I can't push it out anymore at the top is there a simple way to fix this issue so that my front end can be aligned properly once again? Was thinking a longer stud in its place and washers or make a billet solid shim so that there's no chance of the shims falling out after installed. Any ideas? I'm focusin my money to put in a new motor so I can't put a ton into new arms or anything. Posted via Mobile Device
__________________
 Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721 |
|
|
|
04-10-2013, 11:15 PM
|
#2 |
|
Registered User
 
Join Date: Feb 2004
Location: brownfield texas (west texas)
Posts: 1,936
|
Re: Alignment issue
Is the truck dropped? wheel bearing good?
__________________
The Ghost 67 short wide full custom. 550 hp LSX, 4l80E, narrowed 9". Body dropped w/air ride! ........................ ___ .........________//__{\_____ ,,,,,,,/__(⊙)___//___/__(O)_/ @disciple2.rc 💪instagram💪 LED TAILS |
|
|
|
|
04-10-2013, 11:21 PM
|
#3 |
|
Registered User
Join Date: Feb 2012
Location: turlock
Posts: 2,177
|
Re: Alignment issue
Lowered slightly. Wheel bearing should be fine a lot of suspension steering parts were replaced two years ago
Posted via Mobile Device
__________________
Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721 |
|
|
|
|
04-11-2013, 04:44 AM
|
#4 |
|
Registered User
Join Date: Sep 2010
Location: Lake Havasu City Arizona
Posts: 863
|
Re: Alignment issue
Moog makes an offset upper control arm shaft for many car and truck models. While I do not know if yours is included it would be worth checking into.
Posted via Mobile Device
__________________
|
|
|
|
|
04-11-2013, 10:27 AM
|
#5 | |
|
Happy to be here
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: Alignment issue
Quote:
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
|
|
|
|
|
04-11-2013, 10:47 AM
|
#6 |
|
Registered User
Join Date: Jun 2011
Location: Richmond,Va
Posts: 2,934
|
Re: Alignment issue
Most times inner or outer tire wear is associated with toe. Its not hard to assume that tire wear like this is caused by excessive negative camber. As long as the negative camber does not exceed -1.5° tire wear would be a negligible. Have you had a recent alignment. If so, do you have a copy of the results?
__________________
Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever! |
|
|
|
 |
| Bookmarks |
| Tags |
| a-arm, alignment, shims, spacing, stud |
|
|
Linear Mode
