Exhaust before Rear wheels

[77ChevySharkBite]

hey guys, I'm getting ready to finish up my exhaust this month or next I wanted to see picture of your guys exhaust coming out the sides before the rear wheels and right after the gas tank, not sure if it's been covered before or not. This is going to be for a lwb c10 so if you post pictures please note if its swb or lwb.

thanks guys!!

[motornut]

Jimmys?
my 79 hard too see the tips
my 78 dumps down between the tires now

1979 JimmyG Boost from the 78 - YouTube

[77ChevySharkBite]

Yeah that's fine I'm just trying to get ideas, because I don't know if I'll be forced to do it like yours, because I'd really like to run it at an like a 45 degree angle kind of like the svt lightning trucks but single pipe on each side.

[bohmankid]

Mine

http://www.youtube.com/watch?v=Q2ecF1tE9-8

[77ChevySharkBite]

Originally Posted by bohmankid

Mine
http://www.youtube.com/watch?v=Q2ecF1tE9-8

Your truck is sharp looking man!!

I like how yours is ran the tips are awesome! Exact same size I'm looking at doing roughly when where you have the exhaust welded to the tip about how much do you have it pointing down if that makes sense?

[77ChevySharkBite]

I know it's not the best picture but here's my exhaust now, as you can see the further back one you can see where my gas tank is I'm guess I'd have to run it pretty close to my wheel so that I have clearance of my gas tank?

[J Knight]

383 Stroker with Flowmaster Super 44 - YouTube

1986 Chevy C10 Lowrider 383 Stroker - YouTube

[INSIDIOUS '86]

<iframe width="420" height="315" src="https://www.youtube.com/embed/xxKkztunNzM" frameborder="0" allowfullscreen></iframe>

[77ChevySharkBite]

Originally Posted by J Knight

383 Stroker with Flowmaster Super 44 - YouTube


1986 Chevy C10 Lowrider 383 Stroker - YouTube

Very Sharp looking truck man!!! Exhaust sounds awesome!!

[77ChevySharkBite]

Originally Posted by INSIDIOUS '86

<iframe width="420" height="315" src="https://www.youtube.com/embed/xxKkztunNzM" frameborder="0" allowfullscreen></iframe>

it's not letting me get to the video insidious

[bohmankid]

Originally Posted by 77ChevySharkBite

Your truck is sharp looking man!!

I like how yours is ran the tips are awesome! Exact same size I'm looking at doing roughly when where you have the exhaust welded to the tip about how much do you have it pointing down if that makes sense?

Thanks. It's slowly getting put back together. I dunno how much of an angle the pipe is pointing down, I kinda just held it up and welded it redneck style. The whole thing is eye-balled, haha. (I definitely could've done a better job).
The tips are IN 2.5" and OUT 4" with a 45 degree slant. I wanted mine as close to the body as possible so I ditched the saddle tanks. It's inches from the E-brake though, I have to do something about that. You might have to route yours under your leaf spring.

Here's how I had it before I got rid of the saddle tanks. It still woul've looked good with some stainless tips on there:




Hope your getting some good ideas.

[meatwagon83]

Originally Posted by bohmankid

Mine
http://www.youtube.com/watch?v=Q2ecF1tE9-8

your seat cover is awesome!

[bohmankid]

Originally Posted by meatwagon83

your seat cover is awesome!

LOL thanks. The seat is brand new, just upholstered, so I threw that on there to protect it.

[77ChevySharkBite]

Originally Posted by bohmankid

Thanks. It's slowly getting put back together. I dunno how much of an angle the pipe is pointing down, I kinda just held it up and welded it redneck style. The whole thing is eye-balled, haha. (I definitely could've done a better job).
The tips are IN 2.5" and OUT 4" with a 45 degree slant. I wanted mine as close to the body as possible so I ditched the saddle tanks. It's inches from the E-brake though, I have to do something about that. You might have to route yours under your leaf spring.

Here's how I had it before I got rid of the saddle tanks. It still woul've looked good with some stainless tips on there:
Attachment 1097295

Attachment 1097296



Hope your getting some good ideas.

Thanks for the pictures I'm getting some good ideas I'm thinking I could almost take my current dumped pipes and if I pointed them put it would be perfect, and I would just have to figure out how much to point them down so I wouldn't burn my bed any. I really want them to come out at an angle to me it just looks best that way, but I'll have to do some measuring because I don't want to do it and make it look tacky I want it to look nice and clean. I'm trying to keep my saddle tanks because I don't really want to move them and have them remounted.
Posted via Mobile Device

[INSIDIOUS '86]

Spintech 6000 c10 idle - YouTube

This should work. It won't let me embed the video for some reason
Posted via Mobile Device

[77ChevySharkBite]

Originally Posted by INSIDIOUS '86

Spintech 6000 c10 idle - YouTube

This should work. It won't let me embed the video for some reason
Posted via Mobile Device

It worked that time! I like how your's is set up, but I don't want to go through my fender I want it hanging a little, is there anyway you could take some pictures so I can see how you have it done?

Truck sounds very nice btw!

[INSIDIOUS '86]

I have them off now since I've lowered my truck more and I will be running it through the frame and back out the side holes again
Posted via Mobile Device

[77ChevySharkBite]

Originally Posted by INSIDIOUS '86

I have them off now since I've lowered my truck more and I will be running it through the frame and back out the side holes again
Posted via Mobile Device

Oh alright, sounds pretty sweet! When you do it, I'd like to see pictures.