Quick Tune-up Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

lux hauler · 03-20-2002, 04:50 PM

I'm doing a tune-up on my '72 350 and was wondering how do I set the gap on the points?
Do I bring the #1 cyl. to TDC and then set them? What are the supposed to be set at?
The last time I did this was about 15 years ago......now I can't remember.

Thanks

------------------

72 LWB; 350/350,PS,PB,Posi,all original........for now.
99 Ranger

GOD BLESS THE U.S.A.!!!

eagle571@hotmail.com
http://communities.msn.com/196772ChevyTrucks
Vermilion, Ohio

lux hauler · 03-20-2002, 05:27 PM

ttt

Benrs86 · 03-20-2002, 05:31 PM

just tap your starter iwht the distributer cap off untill the points are separated as far as they go. adjust with an allen wrench untill a matchbox lid will hardly fit between them. use a dwell meter if you have one. the meter should read about 28. good lcuk, Ben

69 longhorn · 03-20-2002, 05:34 PM

Just roll the eng so that a dist lobe is at the high point on the points(any lobe),& set the gap @ .019. then roll it to close the points,& slide a business card through to clean the contacts.....69 longhorn.

lux hauler · 03-20-2002, 05:42 PM

thanks y'all.......'preciate it.

03-20-2002, 05:27 PM	#2
lux hauler Psycho-billy Member Join Date: Jul 2001 Location: about 40 miles west of Cleveland, Ohio Posts: 2,591	ttt __________________ '72 C-10 350 w/Lunati Voodoo cam (207/213, .437/.454), Performer intake, 625 Road Demon Jr. and Hooker headers. Support your community, support yourself. Buy local, buy American (or Canadian).

03-20-2002, 05:31 PM	#3
Benrs86 Registered User Join Date: Feb 2000 Location: Brandon, SD, USA Posts: 1,292	just tap your starter iwht the distributer cap off untill the points are separated as far as they go. adjust with an allen wrench untill a matchbox lid will hardly fit between them. use a dwell meter if you have one. the meter should read about 28. good lcuk, Ben __________________ Brandon, SD 69 GMC 1/2 ton 2wd wide long bed with wood 3 on the tree 350 engine 4 bolt main rv cam AIM = Alphray04

03-20-2002, 05:34 PM	#4
69 longhorn Registered User Join Date: Aug 2001 Location: rock island,il,usa Posts: 5,382	Just roll the eng so that a dist lobe is at the high point on the points(any lobe),& set the gap @ .019. then roll it to close the points,& slide a business card through to clean the contacts.....69 longhorn. __________________ http://community.webshots.com/user/hotrodhorn

03-20-2002, 05:42 PM	#5
lux hauler Psycho-billy Member Join Date: Jul 2001 Location: about 40 miles west of Cleveland, Ohio Posts: 2,591	thanks y'all.......'preciate it. __________________ '72 C-10 350 w/Lunati Voodoo cam (207/213, .437/.454), Performer intake, 625 Road Demon Jr. and Hooker headers. Support your community, support yourself. Buy local, buy American (or Canadian).

03-20-2002, 04:50 PM	#1
lux hauler Psycho-billy Member Join Date: Jul 2001 Location: about 40 miles west of Cleveland, Ohio Posts: 2,591	Quick Tune-up Question I'm doing a tune-up on my '72 350 and was wondering how do I set the gap on the points? Do I bring the #1 cyl. to TDC and then set them? What are the supposed to be set at? The last time I did this was about 15 years ago......now I can't remember. Thanks ------------------ 72 LWB; 350/350,PS,PB,Posi,all original........for now. 99 Ranger GOD BLESS THE U.S.A.!!! eagle571@hotmail.com http://communities.msn.com/196772ChevyTrucks Vermilion, Ohio __________________ '72 C-10 350 w/Lunati Voodoo cam (207/213, .437/.454), Performer intake, 625 Road Demon Jr. and Hooker headers. Support your community, support yourself. Buy local, buy American (or Canadian).



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.