|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-19-2013, 11:55 AM
|
#1 |
|
Registered User
Join Date: Feb 2012
Location: Mud Lake, Idaho
Posts: 346
|
Can I pull the pan without pulling the motor?
I need to replace the rear main on my 87 4x4 diesel burb, anybody know if I can get the pan off without pulling the motor? I also need to do the rear main on my dad's 82 diesel 2 wheel drive pickup, anybody done one of those also?
Mike |
|
|
|
10-19-2013, 12:00 PM
|
#2 |
|
BAD BOW-Silverado XST
Join Date: May 2000
Location: Senior Member from Austin, TX
Posts: 6,431
|
Re: Can I pull the pan without pulling the motor?
You can do it on a 4X2. http://www.73-87.com/7387garage/drivetrain/oil_pump.htm
I'm not so sure on a 4X4. |
|
|
|
|
10-19-2013, 01:16 PM
|
#3 |
|
Registered User
Join Date: Sep 2009
Location: Beaverton, OR from WA State
Posts: 1,515
|
Re: Can I pull the pan without pulling the motor?
I had plenty of room under my K25 to pull the pan on my 400sb. Not sure on a 6.2L.
__________________
Devin 1983 GMC High Sierra 2500, 4x4, RC/LB, 400 S.B., SM-465, NP-208, Corporate 10 bolt & 9.5" 14 bolt 1996 GMC Sierra SLE 3500 DRW, 4x4, EC/LB, Vortec 454, NV-4500, BW-4401, AAM 925 & AAM 1050 1997 GMC Sierra SLT 1500 4x4, Z71/F44, EC/SB, Vortec 350 My Introduction with my '83s History New Daily, the '96 |
|
|
|
|
10-19-2013, 05:17 PM
|
#4 |
|
Second Chance Program
Join Date: Jun 2006
Location: Portland, OR
Posts: 2,642
|
Re: Can I pull the pan without pulling the motor?
Not sure on the diesel. But on a 350 4x4, its no problem.
__________________
90 Chevy Suburban 2500 5.3 swap/th400/np241/14bltSF/10blt. 77 C20 crew cab Silverado. 396/th400. In work. |
|
|
|
|
10-19-2013, 06:00 PM
|
#5 |
|
Registered User
Join Date: Sep 2012
Location: Midway, NC
Posts: 3,275
|
Re: Can I pull the pan without pulling the motor?
Wasn't a problem on my truck.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC |
|
|
|
|
10-21-2013, 11:30 AM
|
#6 |
|
Registered User
Join Date: Sep 2012
Location: salem oregon
Posts: 281
|
Re: Can I pull the pan without pulling the motor?
Easy peezy lemon squeezey! Had to pull mine off 2 different motors in the se truck. Get a new gasket for it. Go with a one peace pan gasket, now the rear main is another story. It will take more time and I'm not sure if it's the same as a 350 but u pull the main cap then get a small wood dowel and hammer and tap the top half out. Make sure u pay attention to witch side is facing out. Then do it on your main cap and torque it back down then your hood to go!
__________________
Faith and Patience with my truck, that is what i pray for every day! See my build http://67-72chevytrucks.com/vboard/s...d.php?t=580013 |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
