The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-06-2013, 12:26 AM   #1
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
I bent my DOOR! Won't close now.

I made a huge mistake sigh..I open my door to back up normally when I try to measure how far my rear bumper is or in a tight spot REASON being my stupid mirrors are not adjusted and I can't see sh$&.Anyway today I nearly tore the damn door off by getting it hooked on a pole right near me.My driver door was wide open when it nearly got folded on its back but not quit.The door is preety much bent from stress in the middle and has more importantly has the edges of the fender bent preety good looks like a damn car hit it (folded in).The door sags down about 1 large inch! And doesn't hit the striker I can't close the door.I think it can't close because number because possible mounts or pints OBVIOUSLY but also the fender edge where the door meets fender is so badly folded in and its scuffing and clenching the door.

How much is this going to cost

This is a 82 silverado with done paint job not expensive just normal metallic grey.Rest of truck is fine just door and fender fold
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-06-2013, 12:34 AM   #2
bigwheel15
Registered User
 
bigwheel15's Avatar
 
Join Date: Feb 2010
Location: Fort Worth, TX
Posts: 727
Re: I bent my DOOR! Won't close now.

A junk yard fender and door, around here would set you back around $100. then I'd take it to a couple paint shops and see what they'd charge to match it.
bigwheel15 is offline   Reply With Quote
Old 12-06-2013, 01:08 AM   #3
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

Quote:
Originally Posted by bigwheel15 View Post
A junk yard fender and door, around here would set you back around $100. then I'd take it to a couple paint shops and see what they'd charge to match it.
I mean the door edge that meets the fender is folded in like if some took a big mean axe and slammed it in the edge.The fender is fine I think nothing but bumps and scrapes and some warp but overall straight like new.
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-06-2013, 09:42 AM   #4
old Rusty C10
Robert Olson Transport
 
old Rusty C10's Avatar
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,281
Re: I bent my DOOR! Won't close now.

you may need to do hinges too depends on the severity of the bend
__________________
Bob



1951 International running on a squarebody chassis


"If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board"
http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!)


PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport

Live each day to the fullest.. you never know when fate is going to pull the rug out from under you...
I hate cancer!!
old Rusty C10 is offline   Reply With Quote
Old 12-06-2013, 12:28 PM   #5
Boom
Registered User
 
Join Date: Jan 2012
Location: Klein Texas
Posts: 54
Re: I bent my DOOR! Won't close now.

I gotta ask......when you had the door open did you not see the pole as you passed it up? Post up some pics.
Boom is offline   Reply With Quote
Old 12-06-2013, 01:03 PM   #6
79Betty
Registered User
 
79Betty's Avatar
 
Join Date: Jan 2013
Location: Jasper, IN
Posts: 948
Re: I bent my DOOR! Won't close now.

Put side into the middle of te door with panel and all still on open door. Pull back at back of door? Since it's mashed doubt it'll be saveable
__________________
When in doubt, throttle it out!
1974 Chevrolet Custom K20
2005 Ford Ranger Edge
1985 Chevrolet Custom Deluxe C10
79Betty is offline   Reply With Quote
Old 12-06-2013, 01:57 PM   #7
RastaRobb
Registered User
 
RastaRobb's Avatar
 
Join Date: Sep 2011
Location: Sweet, ID
Posts: 157
Re: I bent my DOOR! Won't close now.

Yeah, we all want pics of that one. Sorry to be a jerk, you are just making me feel better about my screw ups.
RastaRobb is offline   Reply With Quote
Old 12-06-2013, 01:59 PM   #8
RastaRobb
Registered User
 
RastaRobb's Avatar
 
Join Date: Sep 2011
Location: Sweet, ID
Posts: 157
Re: I bent my DOOR! Won't close now.

i backed over my wheel barrow once, and was so ticked off I slammed the door and shattered the glass out of the window. Wife was watching the whole episode and brings it up every once in a while.
RastaRobb is offline   Reply With Quote
Old 12-06-2013, 03:35 PM   #9
crashz
Registered User
 
crashz's Avatar
 
Join Date: Jul 2012
Location: MA
Posts: 207
Re: I bent my DOOR! Won't close now.

Reminds me of the scene in Tommy Boy where Chris Farley did the same thing. "What'd you do!!!!"

Happens to the best of us man. I'd run out of band width before I could finish describing the dumb stuff I've done. Get it fixed up and you'll have a good campfire story.
__________________
2012 Chevy 2500HD, 6.0L, 6spd auto, 4x4, ECSB
1987 GMC V3500 Dump, 6.2L diesel, TH400
1983 GMC K2500 - awaiting its restoration and Cummins swap.
crashz is offline   Reply With Quote
Old 12-06-2013, 05:31 PM   #10
dman1982
Registered User
 
dman1982's Avatar
 
Join Date: Jul 2010
Location: jacksonville nc
Posts: 1,229
Re: I bent my DOOR! Won't close now.

man if you was closer id just give you one, i have a extra one
__________________
Sgt Dennis Heineman
USMC Aviation Ordnance
I.Y.A.O.Y.A.S
2001-Present

84 K10
2000 trans am ws6
2011 nissan altima
2009 Troy Built with a 42 Inch Deck

My LS Swap http://67-72chevytrucks.com/vboard/s...=1#post6559371
dman1982 is offline   Reply With Quote
Old 12-06-2013, 06:03 PM   #11
Doug_J
Registered User
 
Doug_J's Avatar
 
Join Date: Apr 2009
Location: Moore,OK
Posts: 178
Re: I bent my DOOR! Won't close now.

I cant help but laugh reading this I keep thinking of the movie tommy boy and the look on your face must have been priceless something like ... But I'm sorry to hear about the damage hopefully not to bad and it wont cost to much to fix.
Doug_J is offline   Reply With Quote
Old 12-06-2013, 06:07 PM   #12
79Betty
Registered User
 
79Betty's Avatar
 
Join Date: Jan 2013
Location: Jasper, IN
Posts: 948
Re: I bent my DOOR! Won't close now.

I did this exact same thing. Just try bending it back.
__________________
When in doubt, throttle it out!
1974 Chevrolet Custom K20
2005 Ford Ranger Edge
1985 Chevrolet Custom Deluxe C10
79Betty is offline   Reply With Quote
Old 12-06-2013, 09:47 PM   #13
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

Quote:
Originally Posted by Doug_J View Post
I cant help but laugh reading this I keep thinking of the movie tommy boy and the look on your face must have been priceless something like ... But I'm sorry to hear about the damage hopefully not to bad and it wont cost to much to fix.
LMAO the loud crash sound had everyone nearly get off there feet in the diner I was going to eat at and some did look outside.I was more embarrassed then pissed specially trying to kick and snap the door to get it to close.Its funny because what got me scarred was when i put truck in forward the door acted as if it was going to fall off haha.Turns out from further investigation from the mechanic that the door was partially open because below the striker in the very bottom where there is a big slab on the door has a huge indentation.Door is destroyed I'm buying a new one!
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-06-2013, 09:49 PM   #14
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

Quote:
Originally Posted by RastaRobb View Post
Yeah, we all want pics of that one. Sorry to be a jerk, you are just making me feel better about my screw ups.
I will get pics tomarrow
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-06-2013, 10:19 PM   #15
Doug_J
Registered User
 
Doug_J's Avatar
 
Join Date: Apr 2009
Location: Moore,OK
Posts: 178
Re: I bent my DOOR! Won't close now.

Quote:
Originally Posted by chevymadness View Post
LMAO the loud crash sound had everyone nearly get off there feet in the diner I was going to eat at and some did look outside.I was more embarrassed then pissed specially trying to kick and snap the door to get it to close.Its funny because what got me scarred was when i put truck in forward the door acted as if it was going to fall off haha.Turns out from further investigation from the mechanic that the door was partially open because below the striker in the very bottom where there is a big slab on the door has a huge indentation.Door is destroyed I'm buying a new one!
S**t happen at least no one got hurt and it wasn't someone else's car you hit. If its the truck in your avatar it looks clean.
Doug_J is offline   Reply With Quote
Old 12-07-2013, 10:15 AM   #16
donut
Registered User
 
donut's Avatar
 
Join Date: Aug 2009
Location: S.C.
Posts: 1,593
Re: I bent my DOOR! Won't close now.

Fine, I'll do it. (after all, I've had my share of screw-ups. )

__________________
'86 C-30 dually, 454/tbh400
'73 K-20 350/350/205 (sold )

I'm kinda like duct tape- no real purpose, but handy to have around.
donut is offline   Reply With Quote
Old 12-09-2013, 02:19 AM   #17
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:20 AM   #18
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:20 AM   #19
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

[IMG]<a href="http://tinypic.com?ref=2d165y0" target="_blank"><img src="http://i44.tinypic.com/2d165y0.jpg" border="0" alt="Image and video hosting by TinyPic"></a>[/IMG]
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:22 AM   #20
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

[IMG][/IMG]
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:28 AM   #21
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

[IMG][/IMG]
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:30 AM   #22
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

[IMG][/IMG]
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:31 AM   #23
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

[IMG][/IMG]
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 02:38 AM   #24
chevymadness
Registered User
 
Join Date: Aug 2010
Location: el paso texas
Posts: 273
Re: I bent my DOOR! Won't close now.

Got a door off a blazer for 75$ and taking it to get fixed tomarrow.What a screw up this has been.Well hopefully the new door will close like butter because I'm kind of happy this door got what it deserved for making me slam it and slam it all these years!
__________________
1982 chevy silverado

It's all about original guys original let me say again original.
chevymadness is offline   Reply With Quote
Old 12-09-2013, 08:52 PM   #25
TheBlueBomber
Registered User
 
TheBlueBomber's Avatar
 
Join Date: Feb 2013
Location: Cary, NC
Posts: 816
Re: I bent my DOOR! Won't close now.

Dang... Call insurance, make claim, delete thread
__________________
Austin
1996 Chevrolet K1500 Silverado

1979 Chevrolet K10 Scottsdale - Carolina K10 -

My 4.8L Twin turbo build - Project Short Stroke -

Instagram - TheBlueBomber1996
TheBlueBomber is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:04 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com