SC WTB: crank dbl add on pulley. ASAP.

[hardwaycooke]

I need the crank add on to make my ps work. Please let me know
ASAP. Thx. Oh 71 c10 350.

[michael bustamante]

I got one fron a 69 1/2 ton with a 250. 50.00 shipped
Oh sorry.I just saw you have a 350. My bad

[hardwaycooke]

If I could get the dbl add on, or the single add on that puts a gap between the groove against the crank and the outer pulley.

Anything would be helpful. Willing to buy a few different ones to try.

[Ironhorse]

Not sure it will work for you but I have a triple crank pulley, pulled from a '72 Chevy 3/4 ton 350, PS & AC. GM pulley, # 3932428 CH, google showed late
60's to early 70's. $50 shipped, if interested I can do pics for you. Would be tomorrow before I can do pics, in the parts stash somewhere. Right now it's snowing, 6 degrees and wind chill of minus 12. I AM SO READY FOR SPRING

[hardwaycooke]

Originally Posted by Ironhorse

Not sure it will work for you but I have a triple crank pulley, pulled from a '72 Chevy 3/4 ton 350, PS & AC. GM pulley, # 3932428 CH, google showed late
60's to early 70's. $50 shipped, if interested I can do pics for you. Would be tomorrow before I can do pics, in the parts stash somewhere. Right now it's snowing, 6 degrees and wind chill of minus 12. I AM SO READY FOR SPRING

send email for paypal. That's a start. Thanks. Keep em coming.

[Ironhorse]

Sorry but don't have a Paypal account. I always go the money order route when buying or selling on the internet. If you want pics I can send to an email or post here on the board but like I said, will be tomorrow. Pulley is in good shape, I bead blasted, primed and painted it just last fall. Let me know, thanks.

[hardwaycooke]

Originally Posted by Ironhorse

Sorry but don't have a Paypal account. I always go the money order route when buying or selling on the internet. If you want pics I can send to an email or post here on the board but like I said, will be tomorrow. Pulley is in good shape, I bead blasted, primed and painted it just last fall. Let me know, thanks.

ok..send me addy. Like to have it sent priority. need it asap. Thanks

[Ironhorse]

PM sent.

[Classic Bowties]

Originally Posted by Ironhorse

Not sure it will work for you but I have a triple crank pulley, pulled from a '72 Chevy 3/4 ton 350, PS & AC. GM pulley, # 3932428 CH, google showed late
60's to early 70's.

The above mentioned 428 pulley is for long water pump only, the 428 was never "originally" used/installed on these 67-72 trucks which were all short water pump/driver side alt.

69 and later chevy cars = long water pump/pass. side alternator
73 and later GM trucks = long water pump/pass. side alternator

Originally Posted by hardwaycooke

If I could get the dbl add on, or the single add on that puts a gap between the groove against the crank and the outer pulley. Anything would be helpful. Willing to buy a few different ones to try.

Just got your pm, both of the below pictured outer crank p/s add on pulleys were used on the short water pump small blocks trucks. Both have been sandblasted and are ready to ship, would need $40. on the two groove cast iron pulley and $30. on the single groove stamped pulley, shipping on either would be $12.35 USPS priority flat rate and I am headed out to the post office here in a couple of hours, so it could leave today. Could send all of the other column shift indicator parts, column rubbers and column bearings from your other WTB thread all in this same box for the one above shipping charge. Let me know, Mel.

[Classic Bowties]

Hey Dennis, both of the above pictured pulleys went out USPS priority earlier this evening-Sun. 03/02, the projected delivery date listed on the US postal receipt is Wed. 03/05. Thanks again, Mel.