Plastic SB ENGINE MOCKUP'S - The 1947 - Present Chevrolet & GMC Truck Message Board Network

TERRYP · 09-11-2003, 08:32 PM

Does anyone know where to get those SB engine mockup's like I've seen on some TV shows? I also have seen polystyrene trammy's too. Where do I find them, how much?

jeffbo · 09-11-2003, 08:42 PM

I know what you're talking about. I remember seeing an article on them in an old Car Craft or something. This is all I could come up with. I don't think this is the manufacterer of them, just a vendor. Hope this helps.

http://partsboy.com/chevroletreplicaengines.htm

TERRYP · 09-11-2003, 08:49 PM

Just did a search, found P-ayr products, long block is about $350, tranny is $250, too much!

*Randy70C-10* · 09-11-2003, 09:03 PM

Imagine the look on someones face when you bend over and lift one.

They have threaded holes and will accept any bolt-on parts.

68 Suburban · 09-11-2003, 09:38 PM

Here you go:

http://cgi.ebay.com/ebaymotors/ws/eB...&category=6783

*rickspickuppart* · 09-11-2003, 10:19 PM

the one on ebay is a good deal we paid alot more for ours

cdowns · 09-11-2003, 11:20 PM

speedway motors has them

palallin · 09-12-2003, 10:19 AM

You could buy a junk engine for a heckuva lot less

Heck, I sold a decent, 3,000-miles-on-the-rebuild 307 for a lot less!

68lnb · 09-12-2003, 12:04 PM

I had an old block that I had to leave behind when we moved cross country, left it with a freind. I stripped everything out of it, then started drillin holes. I just left the drill there and the cuttin oil. then whenever the mood struck I would drill out a new hole. After a couple of years it was lookin very swiss cheesy. Dont know if it lightened it up all that much but it looked cool and was fun. I also had junk heads (heavy) and a stripped out turbo 350. Total cost was a twelve pack of beer! Wish I had them now. They were handy for mock-up.

lukecp · 09-12-2003, 01:53 PM

I saw one of those at Autozone once.....it was sitting on a little stand that looked way to puny to hold a SBC...i thought it was real until i bumped into it and it easily moved, lol. They fooled me.....

09-12-2003, 02:01 PM

I saw one the other day and I thought it said it was 49.99

09-11-2003, 08:32 PM	#1
TERRYP GYRO GEARLOOSE Join Date: Jun 2000 Location: Nevada City, CAEverett, WA Posts: 361	Plastic SB ENGINE MOCKUP'S Does anyone know where to get those SB engine mockup's like I've seen on some TV shows? I also have seen polystyrene trammy's too. Where do I find them, how much? __________________ Nevada City, CA Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB. 350 from '68, 200R4 tranny, 3.07 rear ratio, restoring 68 C10 LWB 350 4spd, 4.56 rear dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna 85 Tercel SW, snow runner DISGRACED OUTLAW MEMBER OF THE DRUM BRAKE CLUB

09-11-2003, 08:42 PM	#2
jeffbo D.U.F. Member Join Date: Nov 2002 Location: Huron/Brookings, SD Posts: 288	I know what you're talking about. I remember seeing an article on them in an old Car Craft or something. This is all I could come up with. I don't think this is the manufacterer of them, just a vendor. Hope this helps. http://partsboy.com/chevroletreplicaengines.htm __________________ MEMBER OF THE DISCS UP FRONT CLUB '72 C-10 LWB Highlander, A/C, tilt TH350 w/ B&M shift kit, 327LJ bored .040", cast flattops, forged crank, L31 Vortecs, 9.25:1 CR, Comp conical valvesprings, Crane Energizer single pattern 216/.454", Professional Products Power Plus Crosswind intake, Edelbrock #1406 600cfm, HEI, dual exhaust, open 3.08 12bolt '68 C-10 4spd (not running) '79 C-10 LWB Mild 350 '80 Caprice Classic, 2-dr '97 GMC K-1500, SWB, Reg. Cab, Z-71, 5.7, Auto

09-11-2003, 08:49 PM	#3
TERRYP GYRO GEARLOOSE Join Date: Jun 2000 Location: Nevada City, CAEverett, WA Posts: 361	Just did a search, found P-ayr products, long block is about $350, tranny is $250, too much! __________________ Nevada City, CA Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB. 350 from '68, 200R4 tranny, 3.07 rear ratio, restoring 68 C10 LWB 350 4spd, 4.56 rear dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna 85 Tercel SW, snow runner DISGRACED OUTLAW MEMBER OF THE DRUM BRAKE CLUB

09-11-2003, 09:38 PM	#5
68 Suburban Registered User Join Date: Oct 2000 Location: From Chicago, Live in Phoenix, AZ Posts: 6,802	Here you go: http://cgi.ebay.com/ebaymotors/ws/eB...&category=6783 __________________ Just sitting here contemplating contemplation.

09-11-2003, 11:20 PM	#7
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	speedway motors has them __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

09-11-2003, 09:03 PM	#4
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	Imagine the look on someones face when you bend over and lift one. They have threaded holes and will accept any bolt-on parts.

09-11-2003, 10:19 PM	#6
rickspickuppart Account Suspended Join Date: Jul 2003 Posts: 1,284	the one on ebay is a good deal we paid alot more for ours

09-12-2003, 10:19 AM	#8
palallin Registered User Join Date: Jul 2002 Location: St. James, MO Posts: 1,239	You could buy a junk engine for a heckuva lot less Heck, I sold a decent, 3,000-miles-on-the-rebuild 307 for a lot less! __________________ '69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt.

09-12-2003, 12:04 PM	#9
68lnb Registered User Join Date: Sep 2003 Location: Chino Valley AZ Posts: 25	I had an old block that I had to leave behind when we moved cross country, left it with a freind. I stripped everything out of it, then started drillin holes. I just left the drill there and the cuttin oil. then whenever the mood struck I would drill out a new hole. After a couple of years it was lookin very swiss cheesy. Dont know if it lightened it up all that much but it looked cool and was fun. I also had junk heads (heavy) and a stripped out turbo 350. Total cost was a twelve pack of beer! Wish I had them now. They were handy for mock-up. __________________ 68 C20 lnb

09-12-2003, 01:53 PM	#10
lukecp Formerly yellow72custom Join Date: May 2001 Location: Austin, TX Posts: 7,531	I saw one of those at Autozone once.....it was sitting on a little stand that looked way to puny to hold a SBC...i thought it was real until i bumped into it and it easily moved, lol. They fooled me..... __________________ '72 Chevy C10 Mild 350/TH350/3.07. Ochre/White. Old high school ride. '70 GMC C2500 '62 327 4bbl/SM465/4.56-geared Dana 60. White/White. Project or parts truck. '97 Saturn SL DD. 1.9/5-speed. 40+ highway mpg

09-12-2003, 02:01 PM	#11
Linus0014 Guest Posts: n/a	I saw one the other day and I thought it said it was 49.99



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.