CA SBC Performance Parts

[cleszkie]

Clearing out some space in the garage, and the following items are up for sale:

- Edelbrock Performer intake manifold: EDL-2101, about 100k+ miles on it, dirty but still good to go - $30/obo SOLD

- SBC long water pump: No markings cast into pump, new not remanufactured, came on my new crate motor, only used during break-in and dyno testing - $20/obo SOLD

- Melling high volume oil pump: MEL-M55HV, used for approx 560 miles, comes with pick up (MEL-55-S1), steel intermediate shaft (MEL-IS-55E), and mounting bolt - $20/obo SOLD

- Mallory HEI distributor: Comes with MSD "Heat Module" installed (MSD-83647), about 50k+ miles on dizzy, about 560 miles on Heat module - $90/obo

- Mallory Unilite distributor: MAA-4748201H, comes with Mallory coil and Mallory inline surge protector, approx 50k+ miles on dizzy - $50/obo SOLD

- Edelbrock Cam Kit: EDL 2102, comes with lifters but they are not labeled, cam only run for 100 miles. When cam was installed one of the cam gear bolts was over-torqued and sheared off. New cam was ordered and swapped in. Sheared off bolt still in cam but could be removed with a little elbow grease - $50/obo SOLD

- TRW Performance cam: TP 174, Mild performance cam (see spec card below), 100k+ miles on it, very little wear - $15/obo SOLD

- Mickey Thompson cast aluminum valve covers: #103R-50B, clear powdercoat, no oil baffles, but they can be ordered - $50/obo SOLD

All parts are in good working order. Not trying to sell off faulty or broken junk to fellow board members. I can provide additional pictures upon request. Please keep all correspondance within this thread. No PM side bars please. All prices do not include shipping. Thanks.

[cleszkie]

More pics

[cleszkie]

Again more

[cleszkie]

Last pics

[cleszkie]

Last two

[ScottH]

interested in the Mallory Unilite distributor, would u do $50 shipped?

[1968k20]

I will take the water pump,oil pump, and try cam. Will you do $75 shipped to NE Ca?

[leuggy]

are the mt valve covers tall or short and are there any cracks in the casing down around the bolt holes maybe some closer pics of that area

Blaine

[1968k20]

Meant to say TRW cam

[cleszkie]

Originally Posted by ScottH

interested in the Mallory Unilite distributor, would u do $50 shipped?

ScottH - How does $60 shipped sound?

Originally Posted by 1968k20

I will take the water pump,oil pump, and try cam. Will you do $75 shipped to NE Ca?

1968k20 - I will take $75 shipped for the water pump, oil pump, and TRW cam. But I want to make sure you know the combined cost of the parts is only $55 and you are giving me another $20 for shipping. Its a fair deal considering the weight of the parts, but I want to be sure you didn't make a typo You will like the cam. TRW no longer makes that grind, but it was a pretty popular hop up when I installed it. If all is kosher, send payment to my Paypal account at cpleszkiewicz@yahoo.com.

Originally Posted by leuggy

are the mt valve covers tall or short and are there any cracks in the casing down around the bolt holes maybe some closer pics of that area

Blaine

Blaine - I believe they are the short version. But they are taller than the stock covers. No cracks at the mounting flanges. I will post some more pics of that area in a bit. I will also get the part number off them so you can double check if they are tall or short.

[1968k20]

I figured shipping might cost close to $20. I will pp you when I get home late afternoon. Thank you very much!

[afcamaro]

What kinda deal would you make for the intake and valve covers shipped to 66605? Thank you

[1968k20]

$75 sent

[cleszkie]

Originally Posted by 1968k20

I figured shipping might cost close to $20. I will pp you when I get home late afternoon. Thank you very much!

1968k20 - You are welcome Sir.

Originally Posted by afcamaro

What kinda deal would you make for the intake and valve covers shipped to 66605? Thank you

afcamaro - How does $90 shipped sound?

[ScottH]

60 sounds fine, pm me payment info please.

thanks

[leuggy]

Originally Posted by cleszkie

ScottH - How does $60 shipped sound?




1968k20 - I will take $75 shipped for the water pump, oil pump, and TRW cam. But I want to make sure you know the combined cost of the parts is only $55 and you are giving me another $20 for shipping. Its a fair deal considering the weight of the parts, but I want to be sure you didn't make a typo You will like the cam. TRW no longer makes that grind, but it was a pretty popular hop up when I installed it. If all is kosher, send payment to my Paypal account at cpleszkiewicz@yahoo.com.



Blaine - I believe they are the short version. But they are taller than the stock covers. No cracks at the mounting flanges. I will post some more pics of that area in a bit. I will also get the part number off them so you can double check if they are tall or short.

if they have no cracks I would like to buy them and get shipped to my brother in Washington state
Blaine

[72c105speed]

Edelbrock 2101 cam shipped price to 41018?

[cleszkie]

Originally Posted by leuggy

if they have no cracks I would like to buy them and get shipped to my brother in Washington state
Blaine

Blaine - The part number on the valve covers is "103R-50B". See below for requested pictures:

[cleszkie]

More valve cover pics. Valve cover bolts and hold downs included.

[cleszkie]

Originally Posted by 72c105speed

Edelbrock 2101 cam shipped price to 41018?

72c105speed - How does $65 sound? It is heavy.

[cleszkie]

The sale of the Unilite distributor fell through, so it is still available.

[Undone]

Edelbrock cam kit sell?

[cleszkie]

Originally Posted by Undone

Edelbrock cam kit sell?

Still available.

[Undone]

I'll do 60.00 shipped.

[afcamaro]

If the valve covers are not sold id take them and the intake. Would be interested in the uni-lite as well.