71 Cheyenne Build - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hack71 · 01-02-2016, 08:22 PM

Purchased Feb. 2015, Name: 2-15-15 C10 For Sale Pic 3.jpg
Views: 2036
Size: 27.8 KB

Name: 2-21-15 (1) Just Bought it.jpg
Views: 1877
Size: 42.6 KB

Name: 2-21-15 On the way Home.jpg
Views: 1929
Size: 69.8 KB

Hack71 · 01-02-2016, 08:27 PM

New Wheels Before Pics

Hack71 · 01-02-2016, 08:28 PM

New Wheels After Pics

flashed · 01-02-2016, 08:33 PM

Looks nice .

Hack71 · 01-02-2016, 08:39 PM

Valve Guide on #2 Cylinder is bad, so I opted for a Crate Engine, that way I can build the original 350 over time, I bought a Summit Racing 290HP engine.

Hack71 · 01-02-2016, 08:53 PM

First Car Show I entered at OK Tire in Watford City, ND Sept. 2015

Hack71 · 01-03-2016, 10:59 AM

Spid

Hack71 · 01-03-2016, 11:04 AM

Took the Box off for some cab corner work, while off I cleaned up the frame rails and painted with POR15.

Hack71 · 01-03-2016, 11:27 AM

From first glance it appeared I had very little rust to repair, was I mistaken under the rocker panel was rusted, bottom of the door pillars were as well, looks like I will replace the Outer Floor Panel that includes the Inner Rocker Panel, Door Pillars, and Cab Corner, might have to repair one Floor Support or maybe replace it. It appears I have water coming inside the cab running down the kick panel and sitting on the floor were the kick panel, front of the door and the floor meet, Any Ideas Where it is coming from (both sides)? I'll have to pull the cowl to see were the water is coming in.
This will be my first rust repair, I was a little Nervous about cutting "Her" Apart.

Hack71 · 01-03-2016, 11:37 AM

Waiting on Parts....
I'll never get my parts shipped, I keep calling them back adding to the order, lol! First order was the beginning of December three additions to the order plus Christmas and New Years, along with back orders!
Next time around I'll plan it better and have more patients.

Hack71 · 01-03-2016, 11:59 AM

Front Suspension, I decided to replace front suspension components while waiting for my body parts. I decided to go with 2" lowering springs, we replaced upper and lower: Control Arm Shafts and Seals, Ball Joints, inner and outer Tie Rod Ends and Adjusters, Pitman Arm and Idler Arm. we removed, sandblasted and painted upper and lower Control Arms,This was a much bigger under taking than I thought, Thankfully a friend gave me a hand! we spent almost 13 hours to complete this task.

Hack71 · 01-03-2016, 12:01 PM

A few More Pics

**68350** · 01-03-2016, 02:27 PM

Nice progress! Looks like a good winter project

DBK81 · 01-05-2016, 11:47 PM

Man I love that steering wheel!

71swb4x4 · 01-14-2016, 11:02 PM

Hack you bought that truck a couple blocks from my house! I even saw you looking at it I believe you were driving a newer Chevy pickup with North Dakota plates on it.

Hack71 · 01-15-2016, 09:58 PM

Wow, incredible, yes you are correct small world, I bought it and brought it back to Williston, ND. thanks for adding to the thread!

Hack71 · 01-15-2016, 10:01 PM

Update, Still waiting on Brothers Trucks for my parts, getting impatient, hope to have the truck back together by spring time, I miss driving her.

**68350** · 01-15-2016, 10:31 PM

We should see if we can get a c10 or classic car get together this summer.

Hack71 · 01-15-2016, 11:05 PM

Good Idea! Count me in.

Guardrail · 01-15-2016, 11:56 PM

Love your truck Hack71! I see it was built out here in my neck of the woods. Any idea where it was sold new?

Hack71 · 01-16-2016, 11:03 AM

I haven't done a lot of research yet. What I do know is that it came to the Midwest from Portland. The dealer sticker on the tailgate states "Johnson" located in Gunnison Utah, Did a brief google search but did not find a dealer with that name. The bumper is a SAFE-TEE Bumper, American Bumper Sales Co. Portland, Los Angeles. I will probably do a vin search eventually to determine previous history. If anyone recognizes this truck let me know thats always interesting, picture with a topper was on the truck before I got it.

Hack71 · 01-30-2016, 06:06 PM

Parts have arrived!! I got impatient with Brothers Trucks and canceled back ordered parts, Ordered back ordered parts from Classic Industries. In the mean time I ordered a Cruise Control kit from Summit Racing thinking it would give me something to do till the parts got here! Well..... They all showed up on the same day! Time to get to work.

Hack71 · 01-30-2016, 06:16 PM

Time to remove the front end of the truck, hoping to see what caused the water leaking into the cab causing the rust to start on the floor.

Hack71 · 01-30-2016, 06:25 PM

Looks like the Cowl is good along with everything else. At the base of the windshield on each side is a seam with sealer that has lifted, I removed the seam sealer and there's no thru rust it just needs cleaning, resealing and painting, I had expected something worse. Done for today, doors still need to come off then I can start on the floor repair, rocker and cab corner.

flashed · 01-30-2016, 08:53 PM

Once mine was resealed where the old cracked seam sealer was it quit leaking ,hopefully yours will too .Be sure to check the antenna grommet too.

01-02-2016, 08:22 PM	#1
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	71 Cheyenne Build Purchased Feb. 2015,

01-02-2016, 08:28 PM	#3
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build New Wheels After Pics Attached Images

01-02-2016, 08:33 PM	#4
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: 71 Cheyenne Build Looks nice .

01-02-2016, 08:39 PM	#5
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Valve Guide on #2 Cylinder is bad, so I opted for a Crate Engine, that way I can build the original 350 over time, I bought a Summit Racing 290HP engine. Attached Images

01-02-2016, 08:53 PM	#6
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build First Car Show I entered at OK Tire in Watford City, ND Sept. 2015 Attached Images

01-02-2016, 08:27 PM	#2
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build New Wheels Before Pics Attached Images

01-03-2016, 10:59 AM	#7
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Spid Attached Images

01-03-2016, 11:04 AM	#8
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Took the Box off for some cab corner work, while off I cleaned up the frame rails and painted with POR15. Attached Images

01-03-2016, 11:27 AM	#9
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build From first glance it appeared I had very little rust to repair, was I mistaken under the rocker panel was rusted, bottom of the door pillars were as well, looks like I will replace the Outer Floor Panel that includes the Inner Rocker Panel, Door Pillars, and Cab Corner, might have to repair one Floor Support or maybe replace it. It appears I have water coming inside the cab running down the kick panel and sitting on the floor were the kick panel, front of the door and the floor meet, Any Ideas Where it is coming from (both sides)? I'll have to pull the cowl to see were the water is coming in. This will be my first rust repair, I was a little Nervous about cutting "Her" Apart. Attached Images

01-03-2016, 11:37 AM	#10
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Waiting on Parts.... I'll never get my parts shipped, I keep calling them back adding to the order, lol! First order was the beginning of December three additions to the order plus Christmas and New Years, along with back orders! Next time around I'll plan it better and have more patients.

01-03-2016, 11:59 AM	#11
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Front Suspension, I decided to replace front suspension components while waiting for my body parts. I decided to go with 2" lowering springs, we replaced upper and lower: Control Arm Shafts and Seals, Ball Joints, inner and outer Tie Rod Ends and Adjusters, Pitman Arm and Idler Arm. we removed, sandblasted and painted upper and lower Control Arms,This was a much bigger under taking than I thought, Thankfully a friend gave me a hand! we spent almost 13 hours to complete this task. Attached Images

01-03-2016, 12:01 PM	#12
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build A few More Pics Attached Images

01-03-2016, 02:27 PM	#13
68350 Senior Member Join Date: Jan 2002 Location: Williston, ND Posts: 2,999	Re: 71 Cheyenne Build Nice progress! Looks like a good winter project __________________ 68 Chevy CST/10, 50th Anniversary, 327/th400, 373 posi, buckets 68 GMC Shortbox Stepside, 402/th400, Tilt, Tach, Bucket Seats, 3.08 Positraction 69 Chevy Camaro SS, 383, 4 speed, positraction 70 Chevy El Camino SS396, Triple Black, 454/th400, Tach 70 Chevy Shortbox Stepside 4x4, 350/th350, Tilt, Tach, Cab Lights, Bumper Guards, Tow Hooks 70 Chevy 3/4 Longbox, 350/auto, 70k, SURVIVOR 71 Chevy Blazer, CST, 350/auto 71 GMC Sierra K2500, 454, 4 speed, 4.10 posi, 37s 71 Custom/30, Open Road, 350/th400, tilt 72 Chevy Shortbox Fleetside, 496 Stroker/th400, Tilt, Tach, Bucket Seats, 3.42 Posi 72 GMC Sierra Grande 2500. 427/th400, tilt, a/c, tool and stowage, buckets/console, 3.54 posi

01-05-2016, 11:47 PM	#14
DBK81 Registered User Join Date: Jan 2016 Location: Saskatchewan Posts: 357	Re: 71 Cheyenne Build Man I love that steering wheel! __________________ 1972 C10 - It might be old, but it's not slow

01-14-2016, 11:02 PM	#15
71swb4x4 Senior Member Join Date: Nov 2003 Location: Brookings, SD Posts: 10,497	Re: 71 Cheyenne Build Hack you bought that truck a couple blocks from my house! I even saw you looking at it I believe you were driving a newer Chevy pickup with North Dakota plates on it. __________________ Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.



Register or Log In To remove these advertisements.

01-15-2016, 09:58 PM	#16
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Wow, incredible, yes you are correct small world, I bought it and brought it back to Williston, ND. thanks for adding to the thread! __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build

01-15-2016, 10:01 PM	#17
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Update, Still waiting on Brothers Trucks for my parts, getting impatient, hope to have the truck back together by spring time, I miss driving her. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build Last edited by Hack71; 01-15-2016 at 10:24 PM.

01-15-2016, 10:31 PM	#18
68350 Senior Member Join Date: Jan 2002 Location: Williston, ND Posts: 2,999	Re: 71 Cheyenne Build We should see if we can get a c10 or classic car get together this summer. __________________ 68 Chevy CST/10, 50th Anniversary, 327/th400, 373 posi, buckets 68 GMC Shortbox Stepside, 402/th400, Tilt, Tach, Bucket Seats, 3.08 Positraction 69 Chevy Camaro SS, 383, 4 speed, positraction 70 Chevy El Camino SS396, Triple Black, 454/th400, Tach 70 Chevy Shortbox Stepside 4x4, 350/th350, Tilt, Tach, Cab Lights, Bumper Guards, Tow Hooks 70 Chevy 3/4 Longbox, 350/auto, 70k, SURVIVOR 71 Chevy Blazer, CST, 350/auto 71 GMC Sierra K2500, 454, 4 speed, 4.10 posi, 37s 71 Custom/30, Open Road, 350/th400, tilt 72 Chevy Shortbox Fleetside, 496 Stroker/th400, Tilt, Tach, Bucket Seats, 3.42 Posi 72 GMC Sierra Grande 2500. 427/th400, tilt, a/c, tool and stowage, buckets/console, 3.54 posi

01-15-2016, 11:05 PM	#19
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Good Idea! Count me in. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build

01-15-2016, 11:56 PM	#20
Guardrail And Don't Call Me Shirley Join Date: Oct 2005 Location: Cameron Park, CA Posts: 115	Re: 71 Cheyenne Build Love your truck Hack71! I see it was built out here in my neck of the woods. Any idea where it was sold new? __________________ Rick Tucker 1969 C20/Custom Camper (the Green Machine)Sold 1970 GMC 4000 COE (future Ramp Truck) 1972 K10 Longbed (restoration begins June 2020)

01-16-2016, 11:03 AM	#21
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build I haven't done a lot of research yet. What I do know is that it came to the Midwest from Portland. The dealer sticker on the tailgate states "Johnson" located in Gunnison Utah, Did a brief google search but did not find a dealer with that name. The bumper is a SAFE-TEE Bumper, American Bumper Sales Co. Portland, Los Angeles. I will probably do a vin search eventually to determine previous history. If anyone recognizes this truck let me know thats always interesting, picture with a topper was on the truck before I got it. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build

01-30-2016, 06:06 PM	#22
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Parts have arrived!! I got impatient with Brothers Trucks and canceled back ordered parts, Ordered back ordered parts from Classic Industries. In the mean time I ordered a Cruise Control kit from Summit Racing thinking it would give me something to do till the parts got here! Well..... They all showed up on the same day! Time to get to work. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build Last edited by Hack71; 01-30-2016 at 06:26 PM.

01-30-2016, 06:16 PM	#23
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Time to remove the front end of the truck, hoping to see what caused the water leaking into the cab causing the rust to start on the floor. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build

01-30-2016, 06:25 PM	#24
Hack71 Registered User Join Date: Feb 2015 Location: Bayboro, North Carolina Posts: 180	Re: 71 Cheyenne Build Looks like the Cowl is good along with everything else. At the base of the windshield on each side is a seam with sealer that has lifted, I removed the seam sealer and there's no thru rust it just needs cleaning, resealing and painting, I had expected something worse. Done for today, doors still need to come off then I can start on the floor repair, rocker and cab corner. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=693490Cheyenne, AKA "Spare Change" Hack71 Build

01-30-2016, 08:53 PM	#25
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: 71 Cheyenne Build Once mine was resealed where the old cracked seam sealer was it quit leaking ,hopefully yours will too .Be sure to check the antenna grommet too.

Register or Log In To remove these advertisements.