|
08-13-2016, 09:34 PM
|
#1 |
|
Registered User
Join Date: Aug 2016
Location: Sherwood, Arkansas
Posts: 2
|
Fuel filler neck
I am new to this site --- I have 48 chevy panel truck, Have built custom fuel tank and relocated to rear behind axle, tank is in area that oringinally held spare tire I am hoping that someone can give me an idea about locating and building a filler neck, on drivers side. Thanks for any advice
|
|
|
|
08-13-2016, 09:39 PM
|
#2 |
|
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: Fuel filler neck
This is what I did using a hinge I got off some car at the wrecking yard (don't remember what kind of car.)
   It's sitting in my back yard, one day I'll get back to it. Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
|
|
|
|
08-13-2016, 10:50 PM
|
#3 |
|
Post Whore
  
Join Date: May 2015
Location: Alabama
Posts: 14,674
|
Re: Fuel filler neck
Someone on here had a nice setup in the side of their bed behind the rear fender..I think they used a door from some small ford van that had a cable release on it run to the cab..its a slick setup and I wish I could remember who it was..
|
|
|
|
08-14-2016, 08:45 AM
|
#4 |
|
Registered User
Join Date: Jun 2012
Location: wind lake WI
Posts: 1,752
|
Re: Fuel filler neck
check out my build thread start at#61, hopes this helps.
__________________
LIL ERV the 50-3600 396 BBC stroked to 415 cid Richmond 6spd over drive C4 rear Porter built a arms Never give the Devil a ride,because he'll want to Drive! |
|
|
|
|
08-14-2016, 12:51 PM
|
#5 | |
|
Registered User
Join Date: Aug 2016
Location: Sherwood, Arkansas
Posts: 2
|
Quote:
Thanks but I do not know how to get to you Thread, can you tell me how to get there. I am technologically challenged Posted via Mobile Device |
|
|
|
|
|
08-14-2016, 01:09 PM
|
#6 |
|
Post Whore
Join Date: May 2015
Location: Alabama
Posts: 14,674
|
Re: Fuel filler neck
Billy..click on the blue writing in his post that says (lil erv the 50-3600.).I think his gas filler install starts on page 4..
|
|
|
|
|
08-14-2016, 11:35 PM
|
#7 |
|
Senior Member
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
|
Re: Fuel filler neck
Pics are not the best but,
Pic 1 This is a Hagan door installed in the drivers rear fender. Pic 2 The back side showing the short elbow installed on the Hagan fitting Pic 3 My tank showing outlet from tank. I used regular gasoline hose to connect the two. Hope this helps...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
