Ls swap donor...what's needed?

[tex_waco_usmc]

I just recently acquired an 01 2500hd with 6.0 and 4l80 tranny. What all do I need to pull off the donor truck to do the swap. Momma doesn't want this truck sitting in our driveway long(body is very rough)! Please help don't want to get rid of anything I'll need.

[nastety92]

Engine
Engine wiring harness
Transmission
ECM / PCM
Gas Pedal
Air Intake if your going to use the stock one
Might as well keep the fuse block under the hood
Overflow tank
Mechanical fan if your going to run that

On my swap I'm trying to make it look 100% stock under the hood. Other people have done custom air intakes and electric fans.

Also is the truck going to be 4wd or 2wd in the end?

Good luck,
Nick

[tex_waco_usmc]

2wd in a short bed 67. Do I need cross members, etc?

[nastety92]

Originally Posted by tex_waco_usmc

2wd in a short bed 67.

Is the 2500HD 2wd or 4wd?

[t300]

If you really want to get everything you can off it it then add throttle cable, cruise control box and cable, rear view mirror and temp sensor/wiring, I used a bunch of the exhaust piping to build my exhaust as well. 7pin trailer wiring, hitch may be able to be used. Saw a post here where someone used the rear brake calipers with a custom bracket. Apparently door molding can be used. Some have used the front bench seat or buckets.

[tex_waco_usmc]

Originally Posted by nastety92

Is the 2500HD 2wd or 4wd?

2wd

[69gmcc10]

I have an 01 1500 sitting in my driveway for the same purpose and it has been there for a year and 4 months, my wife is not impressed. I am very close to getting the engine swap part of the project completed, I have to install the wiring loom I cleaned up on my own and run fuel lines and I should be done with the donor truck.

From the donor truck I have used the engine and trans, the power steering cooler, trans cooler, trans lines, wiring harness for the engine, the fuse block. I am going to try and use the in cab section of the wiring for the cruise, cluster, & obdII. I also used the radiator air intake, coolant overflow, computer mount, cruise control box off the fire wall, and throttle cable. Before I junk the truck I am going to snag the front seats to retrofit and I am going to see if the carpet will fit (I have a high hump). Other things to consider are maybe the fuel door (if you plan to put the tank out back) and the cruise switch from the turn indicator if you are going to install cruise.

good luck

[Jstock85]

Originally Posted by 69gmcc10

I have an 01 1500 sitting in my driveway for the same purpose and it has been there for a year and 4 months, my wife is not impressed. I am very close to getting the engine swap part of the project completed, I have to install the wiring loom I cleaned up on my own and run fuel lines and I should be done with the donor truck.

From the donor truck I have used the engine and trans, the power steering cooler, trans cooler, trans lines, wiring harness for the engine, the fuse block. I am going to try and use the in cab section of the wiring for the cruise, cluster, & obdII. I also used the radiator air intake, coolant overflow, computer mount, cruise control box off the fire wall, and throttle cable. Before I junk the truck I am going to snag the front seats to retrofit and I am going to see if the carpet will fit (I have a high hump). Other things to consider are maybe the fuel door (if you plan to put the tank out back) and the cruise switch from the turn indicator if you are going to install cruise.

good luck

What you doing for your fuel system?

[Jstock85]

Originally Posted by nastety92

Engine
Engine wiring harness
Transmission
ECM / PCM
Gas Pedal
Air Intake if your going to use the stock one
Might as well keep the fuse block under the hood
Overflow tank
Mechanical fan if your going to run that

On my swap I'm trying to make it look 100% stock under the hood. Other people have done custom air intakes and electric fans.

Also is the truck going to be 4wd or 2wd in the end?

Good luck,
Nick

Nick how are you mounting the stock overflow tank? I was considering the same. Just curious.

[69gmcc10]

Originally Posted by Jstock85

What you doing for your fuel system?

1989 blazer 24 gal tank under the bed with an 89 sending unit and a AC delco ep381 pump in the tank.

[faun_cee]

Originally Posted by nastety92

Engine
Engine wiring harness
Transmission
ECM / PCM
Gas Pedal
Air Intake if your going to use the stock one
Might as well keep the fuse block under the hood
Overflow tank
Mechanical fan if your going to run that

On my swap I'm trying to make it look 100% stock under the hood. Other people have done custom air intakes and electric fans.

Also is the truck going to be 4wd or 2wd in the end?

Good luck,
Nick

I have an uncle ( who has never done an LS ) telling me I NEED to swap out the rear end or change the gears to not blow the rear end. is this true?

[65blackfleetside]

Originally Posted by faun_cee

I have an uncle ( who has never done an LS ) telling me I NEED to swap out the rear end or change the gears to not blow the rear end. is this true?

What rear end are you running? stock chevy 10 bolt should be fine.