Big block C10 short step coil spring exhaust hanger help! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ghalperin · 05-24-2017, 12:53 PM

I'm laying out my Pypes 2 1/2 exhaust system and my GM exhaust hangers. I've got one more hanger being delivered and I have new rubber inserts.

It looks like 4 hang vertically from the frame and 2 hang horizontally from a crossmember. I do have the small crossmember that I removed for my Blazer tank installation. I didn't see any predrilled holes in the frame that look like they would work.

I'm using the factory crossmember for the transmission bellhousing mount.

Where should I put the hangers on my 67 frame?

Name: IMG_7025.jpg
Views: 460
Size: 66.3 KB

Name: IMG_7025.jpg
Views: 460
Size: 66.3 KB

Name: IMG_7026.jpg
Views: 420
Size: 65.3 KB

Name: IMG_7027.jpg
Views: 393
Size: 68.6 KB

ghalperin · 05-24-2017, 04:41 PM

I found some photos...
Name: attachment6T33VRNW.jpg
Views: 361
Size: 41.1 KB

Name: attachmentBP7SFGS8.jpg
Views: 355
Size: 41.6 KB

Name: attachmentR5369NR2.jpg
Views: 346
Size: 39.8 KB

Name: attachmentZL5K092Q.jpg
Views: 342
Size: 41.8 KB

Name: muffler hanger.jpg
Views: 384
Size: 51.1 KB

**70STOVEBOLT** · 05-24-2017, 05:01 PM

I don't have an answer to your question, but can you tell me what the measurements are between the pipes on the x-pipe? I have been contemplating using the Pypes system on my truck but I am not sure I can use it with my current mufflers as they have center inlets and outlets.

ghalperin · 05-26-2017, 02:11 PM

Quote:

Originally Posted by 70STOVEBOLT

I don't have an answer to your question, but can you tell me what the measurements are between the pipes on the x-pipe? I have been contemplating using the Pypes system on my truck but I am not sure I can use it with my current mufflers as they have center inlets and outlets.

I have the exhaust boxed up, but will measure it for you this weekend.

Keep in mind that the x-pipe is 5 separate pieces and you cut it to size. The width can get pretty narrow, if needed.

**70STOVEBOLT** · 05-26-2017, 05:35 PM

Glenn, thank you I appreciate it. Have a good weekend.

ghalperin · 06-03-2017, 11:02 AM

Name: IMG_7104.jpg
Views: 255
Size: 81.7 KB

I measured 22" outside on one end and 37" outside on the other. Either side could be as narrow as ~12". The welds on the X-pipe are stainless and are very nice.

I ended up returning the system and had a custom exhaust made. The factory hangers wouldn't work as I wanted the exhaust tucked up high.

**70STOVEBOLT** · 06-03-2017, 11:35 AM

Glenn, thank you for taking the time to post this. What P/N was the Pypes system? I was looking at SGT 79 for our trucks and their tech dept told me the outlet legs on the x-pipe were only 13" apart which would not work for me, as I am tucking my exhaust up between the frame rails as well,and routing through the trailing arm crossmember.

05-24-2017, 12:53 PM	#1
ghalperin Registered User Join Date: Jul 2016 Location: Newport Heights, CA Posts: 1,000	Big block C10 short step coil spring exhaust hanger help! I'm laying out my Pypes 2 1/2 exhaust system and my GM exhaust hangers. I've got one more hanger being delivered and I have new rubber inserts. It looks like 4 hang vertically from the frame and 2 hang horizontally from a crossmember. I do have the small crossmember that I removed for my Blazer tank installation. I didn't see any predrilled holes in the frame that look like they would work. I'm using the factory crossmember for the transmission bellhousing mount. Where should I put the hangers on my 67 frame? __________________ Glenn 1960 Burro Corvair/VW Buggy - Factory made in Santa Ana, Ca 1929 Ford Model A Roadster - traditional pre-war banger hot rod

05-24-2017, 04:41 PM	#2
ghalperin Registered User Join Date: Jul 2016 Location: Newport Heights, CA Posts: 1,000	Re: Big block C10 short step coil spring exhaust hanger help! I found some photos... __________________ Glenn 1960 Burro Corvair/VW Buggy - Factory made in Santa Ana, Ca 1929 Ford Model A Roadster - traditional pre-war banger hot rod

05-24-2017, 05:01 PM	#3
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,414	Re: Big block C10 short step coil spring exhaust hanger help! I don't have an answer to your question, but can you tell me what the measurements are between the pipes on the x-pipe? I have been contemplating using the Pypes system on my truck but I am not sure I can use it with my current mufflers as they have center inlets and outlets. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

05-26-2017, 05:35 PM	#5
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,414	Re: Big block C10 short step coil spring exhaust hanger help! Glenn, thank you I appreciate it. Have a good weekend. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear Last edited by 70STOVEBOLT; 06-07-2017 at 02:58 PM.

06-03-2017, 11:02 AM	#6
ghalperin Registered User Join Date: Jul 2016 Location: Newport Heights, CA Posts: 1,000	Re: Big block C10 short step coil spring exhaust hanger help! I measured 22" outside on one end and 37" outside on the other. Either side could be as narrow as ~12". The welds on the X-pipe are stainless and are very nice. I ended up returning the system and had a custom exhaust made. The factory hangers wouldn't work as I wanted the exhaust tucked up high. __________________ Glenn 1960 Burro Corvair/VW Buggy - Factory made in Santa Ana, Ca 1929 Ford Model A Roadster - traditional pre-war banger hot rod

06-03-2017, 11:35 AM	#7
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,414	Re: Big block C10 short step coil spring exhaust hanger help! Glenn, thank you for taking the time to post this. What P/N was the Pypes system? I was looking at SGT 79 for our trucks and their tech dept told me the outlet legs on the x-pipe were only 13" apart which would not work for me, as I am tucking my exhaust up between the frame rails as well,and routing through the trailing arm crossmember. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear Last edited by 70STOVEBOLT; 06-03-2017 at 11:40 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.