|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-15-2020, 11:17 PM
|
#1 |
|
Registered User
Join Date: Jan 2020
Location: Meridian
Posts: 11
|
Glove Box Door Emblem Question
I have a 72 C10 and I noticed that my glovebox door has two little holes, one on each side. Can anyone tell me what emblem it should have on it? I'm assuming the holes are for emblems. Thanks! See attached pic.
|
|
|
|
08-16-2020, 01:23 AM
|
#2 |
|
Senior Member
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,870
|
Re: Glove Box Door Emblem Question
My 72 Blazer says "Chevrolet CST" on the glove box door, but the emblem is only about half that width, and there are three mounting holes.
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson |
|
|
|
|
08-16-2020, 08:53 AM
|
#3 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: Glove Box Door Emblem Question
Tell us about your truck. It looks like maybe the holes for the wide Chevrolet emblem from 67/68, although they seem wide and high, as well as small diameter. Not all trucks got an emblem. Not only some basic trucks didn't, but the Cheyenne/Sierras also did not, for example
67/68 emblem
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
08-16-2020, 09:19 AM
|
#4 |
|
Registered User
Join Date: Jan 2020
Location: Meridian
Posts: 11
|
Re: Glove Box Door Emblem Question
What kind of information would help? I have the VIN and the Door Plate, but I'm not sure what trim level it was originally unless I can tell by that information somehow.
|
|
|
|
|
08-16-2020, 10:02 AM
|
#5 |
|
Roadtrip!
Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,712
|
Re: Glove Box Door Emblem Question
Doesn't look like factory to me.
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
|
|
|
|
08-16-2020, 11:21 AM
|
#6 |
|
Proprietor of Dale's Corner
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 15,963
|
Re: Glove Box Door Emblem Question
I'm guessing your spid is missing? Those holes don't look factory....
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man |
|
|
|
|
08-16-2020, 02:25 PM
|
#7 |
|
Registered User
Join Date: Jun 2014
Location: Tahuya WA
Posts: 536
|
Re: Glove Box Door Emblem Question
I believe mine was an old OD green Bell Telephone work truck.
You can see where there are 4 holes above the lighter for a microphone, (probably should get a CB) and the glove box door had a couple holes in it from some emblem that used to be there. I just found an emblem to cover the holes in the door, so that thing is in the wrong location, but who cares, I like it. 
|
|
|
|
| Bookmarks |
|
|
Linear Mode
