The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-30-2021, 12:55 AM   #1
wazzabie
Registered User
 
Join Date: Dec 2011
Location: WA
Posts: 378
Door gap woos

I'm trying to get my door gaps to spec. The manual says .19in top and sides. The bottom is .25in. The .25in is about 3 popsicle sticks and the .19in is two popsicle sticks. I replaced the door pins on the driver side.

- On my drivers side on the rear side the gap is wide. It is like 4-5 popsicle sticks.

- On my passenger side the rear side gap is too tight. It is like like zero popsicle sticks.

At some point it has been hit in both fenders. Maybe my body been tweaked.

Is it odd to be wide in gap on one side and tight on the other side? Was this indicate a tweaked body?
wazzabie is offline   Reply With Quote
Old 10-30-2021, 04:27 AM   #2
Danmcg
Registered User
 
Join Date: Jun 2014
Location: Central NY
Posts: 168
Re: Door gap woos

Quote:
Originally Posted by wazzabie View Post
Is it odd to be wide in gap on one side and tight on the other side? Was this indicate a tweaked body?
No, not odd at all, Who knows what the last guy did. What I find odd is you're using popsicle sticks ...lol

Use a 3/16 drill bit with some masking tape on it for 0.19" and a 1/4 bit for the 0.25"
Danmcg is offline   Reply With Quote
Old 10-30-2021, 06:58 AM   #3
TKCR
Senior Member
 
TKCR's Avatar
 
Join Date: Oct 2014
Location: Ohio
Posts: 6,979
Re: Door gap woos

There’s just a lot of adjustments that need to be made. I went to change my pins & bushings, but ended up replacing all the hinges. One was bent, and the drivers side, the S spring was upside down. So if I had just done the pins & pushing, I would have still had problems with the drivers door because of that S spring being upside down. And it was the passenger side that was bent.
I also replaced the strikers. It important to have those bushings on the strikers. So that will play a part in getting your doors adjusted. Along with all those new parts, I also replaced the door latches and all the seals. So since the doors were off and all those new parts, I had a lot of time & effort in getting those doors lined up and closing nicely. It’s going to be a combination of adjusting the hinge bolts to the doors, and I also had to do some adjusting of the fender side also. Then adjusting the striker, but I finally got it. I won’t say my gaps are within specs, but they are pretty even around the entire door. I was more focused on getting those doors closing with ease. And that I accomplished! No more slamming the doors 3-4 times. It closes the first time.
https://youtu.be/G-kBGflFUfY
Attached Images
  

Last edited by TKCR; 10-30-2021 at 07:03 AM.
TKCR is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:45 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com