badging - The 1947 - Present Chevrolet & GMC Truck Message Board Network

71Rat · 02-09-2004, 02:13 AM

would an emblem that says "C/10" fit in the same holes as a "custom/10"? i am wondering if anyone has tried to swap them or seend if the pins are the same with apart.... i assume GM wouldn't change the holes in the tooling just for one little emblem

Thanks
Rat

Tx Firefighter · 02-09-2004, 08:25 AM

They drop right inthe same holes.

71Rat · 02-09-2004, 04:23 PM

Ok thank you, thats all i needed to know.

thanks
Rat

mrein3 · 02-10-2004, 12:06 AM

Not that I doubt Tx Firefighter but I know for a fact cheyenne and C/10 emblems use the same holes...

mrein3 · 02-10-2004, 12:07 AM

on my short list for this spring is to fill up the "extra" holes and squirt this fender the correct color for me...

71Rat · 02-10-2004, 12:28 AM

mrein3: thanks for the photos to even prove it.... i was thinking of smoothing the fender but i also liked the "c/10" badging so i might put them on for a little bit.

Thanks again

Rat

Longhorn Man · 02-10-2004, 12:47 AM

Don't try this with a chevy badge on a GMC fender though....or vise-versa.

02-09-2004, 02:13 AM	#1
71Rat ran out of money Join Date: Apr 2003 Location: northern, NJ Posts: 925	badging would an emblem that says "C/10" fit in the same holes as a "custom/10"? i am wondering if anyone has tried to swap them or seend if the pins are the same with apart.... i assume GM wouldn't change the holes in the tooling just for one little emblem Thanks Rat __________________ Modify everything, leave nothing alone!~

02-09-2004, 08:25 AM	#2
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	They drop right inthe same holes. __________________ I'm on the Instagram- @Gearhead_Kevin

02-09-2004, 04:23 PM	#3
71Rat ran out of money Join Date: Apr 2003 Location: northern, NJ Posts: 925	Ok thank you, thats all i needed to know. thanks Rat __________________ Modify everything, leave nothing alone!~

02-10-2004, 12:06 AM	#4
mrein3 Registered User Join Date: Feb 2000 Location: Center City, MN, USA Posts: 3,254	Not that I doubt Tx Firefighter but I know for a fact cheyenne and C/10 emblems use the same holes... Attached Images __________________ '70 cab, '71 chassis, 383, TH350, NP205. '71 Malibu convertible '72 Malibu hard top Center City, MN

02-10-2004, 12:07 AM	#5
mrein3 Registered User Join Date: Feb 2000 Location: Center City, MN, USA Posts: 3,254	on my short list for this spring is to fill up the "extra" holes and squirt this fender the correct color for me... Attached Images __________________ '70 cab, '71 chassis, 383, TH350, NP205. '71 Malibu convertible '72 Malibu hard top Center City, MN

02-10-2004, 12:28 AM	#6
71Rat ran out of money Join Date: Apr 2003 Location: northern, NJ Posts: 925	mrein3: thanks for the photos to even prove it.... i was thinking of smoothing the fender but i also liked the "c/10" badging so i might put them on for a little bit. Thanks again Rat __________________ Modify everything, leave nothing alone!~

02-10-2004, 12:47 AM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Don't try this with a chevy badge on a GMC fender though....or vise-versa.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.