GA WIW 71 2wd blazer

[blazerboy72]

Im not sure if this is where this belongs, if not please move it. I am considering selling my factory 2wd blazer. It is a 71 on air bags (not plumbed but do have all fittings and lines to use shrader valves). The engine is an 01 5.3 (30K miles) with a comp big mutha thumpr cam, ls6 springs and it is tuned. It also has a 4l80e with a 2500 stall. The transmission is in but not fully installed. I have the shift linkage, flexplate and spacer to complete installation. It also has a new gas tank, walbro fuel pump, hooker headers, new brake booster, master cylinder, prop. valve,and rear disk brakes. I had started installing a step notch in the rear but so far I have only cut the floor to clear the notch (which I cut down to only raise the floor 4" so I could keep the rear seat), the frame is untouched. I have many new in the box parts including new autometer gauges in a new bezel, new rockers, rear floor section, rear cross brace, new tailgate, new rocker box for the drivers side, uncut ac dash, and im sure some other stuff. There is a little rust in the rear floor section and the drivers side floor which I had started to repair but never finished. I also have rack and pinion for a drop member I would include. Im not certain I want to sell it and have no idea what it would be worth. So what is it worth?

[Liddy71]

looks like a nice ride I would say any where from 45-6000 depends on the work done and parts like the Ls wiring ,seats,body panels.

[blazerboy72]

That is about what I was thinking. I just cant bring myself to sell her. Ill put her in storage until im motivated to work on her again.

[bluespark56]

Hi, if the body's solid, let me know when you decide to sell. thanks, bye.

[blazerboy72]

Body has a little rust but I have all patch panels to repair it. Let me know if you are interested.

[bluespark56]

Hi, I know about the a/c dash picture, but what are the rest of the pics?, also do you have any more pics?..... do you really want to sell? I might be interested if the price is right?,, thanks bye,

[blazerboy72]

The other picture is some of the patch panels for it. Im going to try to get pictures today if I can find the camera.

[blazerboy72]

Here are a few pics

[blazerboy72]

few more

[blazerboy72]

The motor is wired and has been reprogrammed for the cam. I have not reprogrammed it for the 4l80e. The seats are complete but need to be recovered. I also have a spare tire carrier I can throw in. I will sell all or part. I wouldnt mind keeping the motor and trans if someone wants the body and suspension. I also have 3 front crossmembers, 1 stock 1 sectioned, and custom built that needs to be finished. The custom one is similar to the original drop member. It still needs lower control arm mounts and mounts for the rack.

[bluespark56]

Hi, blazerboy72, what's the least you'd take for it as is?...... and price without motor/trans (body & susp.& parts only?..... Why are you selling?... thanks , bye... blue.

[blazerboy72]

Im selling trying to fund a land purchase, and I dont have the time or money to finish the truck the way it should be done. I need $5500 for the complete project. $2500 for body and frame. $4500 with out motor and trans.

[bluespark56]

Hi, for $2500 exactly what would I get. also, can I get a ph. #,,,,,, thanks, bye .

[blazerboy72]

Body with original hood and fenders, stock frame, rear axle, all 3 front crossmembers, and you can have the air bags and step notch which I cut down so I could still use a rear seat. I would keep all the aftermarket replacement parts.

[SWB4x4]

how much for the motor and trans? also interested in tank and fuel system for it.

[blazerboy72]

I would like to keep the engine and trans unless someone buys it all.