|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-21-2015, 02:57 PM
|
#1 |
|
Registered User
Join Date: Jun 2015
Location: Baton Rouge Louisiana
Posts: 26
|
1971 differential bearings? - help needed
My truck is a 1971 with a 12-bolt differential. The SPID lists G80 rear positrac axle.
I want to change the rear wheel bearings, seals and the pinion oil seal and would like to use the best quality products available. I have heard great things about Timken products. Been looking around on the Internet and been to NAPA etc but I could use some advice on getting the correct parts. The guy at NAPA wasn't clear on what I needed. Rockauto lists the bearings for a DANA/Spicer rear end (#387A) and also the Timken (SET36) with no diff manufacturer listed. Are these correct for my differential? Any help/suggestions are greatly appreciated. Thank you. |
|
|
|
10-21-2015, 11:42 PM
|
#2 |
|
horsepower junkie
Join Date: Aug 2003
Location: graham, washington
Posts: 326
|
Re: 1971 differential bearings? - help needed
__________________
67  short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH |
|
|
|
|
10-22-2015, 08:21 AM
|
#3 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: 1971 differential bearings? - help needed
I like RockAuto, but you need to know exactly what you need/want. The link above is good and use the phone to call them, tell them what you have, and place your order.
The 12 bolt is NOT the Dana Axle.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
10-22-2015, 08:26 AM
|
#4 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: 1971 differential bearings? - help needed
When i redid my 12bolt rear i walked into carquest and after a cup of coffee i walked out with the bearings in my hand
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
10-23-2015, 09:20 PM
|
#5 |
|
Registered User
Join Date: Jun 2015
Location: Baton Rouge Louisiana
Posts: 26
|
Re: 1971 differential bearings? - help needed
Great information. I wasn't familiar with that website.
Thanks! |
|
|
|
|
10-25-2015, 11:14 AM
|
#6 |
|
Senior Member
 
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,414
|
Re: 1971 differential bearings? - help needed
Timken or Bower (Federal Mogul) are both US made.
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
