|
|
|
|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools
|
Display Modes
|
|
|
05-19-2016, 11:45 AM
|
#1 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
Here is after the frame shop worked on it. Got it up on stands and got as close as I could to the measurements from before mentioned sheet. See that the frame shop tweaked the front the other way.
|
|
|
|
05-19-2016, 11:49 AM
|
#2 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
So I verified all the measurements, found center of frame on all the sections I thought were good and locked the frame down then jacked the front up and pulled it a few times to the side. Now the frame is with in 1/8 of center line and all the heights are with in a 1/4 of each other. put a few tack welds and a temporary x brace in. Going to lower it down tonight and set frame on ground and check all the measurements again before welding it back up and boxing frame.
|
|
|
|
|
05-20-2016, 09:14 AM
|
#3 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
Got it down on the ground and all looks pretty good. At least I'm happy with it for moving forward. Real sad I couldn't get any frame shops here in town to help me out. Going to weld it tonight and hopefully box some of the frame rails to strengthen it. Then cut some pockets for the sway bar. Tacked the bumper bolts while I was tacking the frame. Going to try and shave the bumper.
|
|
|
|
|
05-22-2016, 08:54 PM
|
#4 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
well got the cups for the steering welded back in. Also got the cups in for raising the sway bar in as well. Frame stiffed up really well. Not going to worry about boxing it.
|
|
|
|
|
05-22-2016, 08:56 PM
|
#5 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
Got the motor and cab back on to start welding up the cab floor.
|
|
|
|
|
05-22-2016, 09:01 PM
|
#6 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
Got started on the drive shaft tunnel. Ran out of cutting wheels half way through. Wife was out so waiting on her to bring me some back. Got bored and started filling in holes. LOL. going to need some putty for sure!! I want to fill in that cab seam as well. Would just welding it then grinding it off be the best bet??
|
|
|
|
|
05-22-2016, 09:05 PM
|
#7 |
|
Registered User
Join Date: Apr 2013
Location: wilmington nc
Posts: 492
|
Re: 83/84 swb stepside long time build
Almost got done with the drive shaft tunnel, but rain came in and had to stop. Got one weld left along the top. The little Hobart 125 does pretty good with sheet metal.I have gas, but going to wait till I do external stuff.
|
|
|
|
|
| Bookmarks |
|
|
rip2174 
Hybrid Mode
