His name is "George" 84' C10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOTI · 04-29-2021, 09:41 AM

Looks 'complicatingly' good. I bet wrapping was fun as well.

WilliamFd55 · 04-29-2021, 02:37 PM

Quote:

Originally Posted by SCOTI

Looks 'complicatingly' good. I bet wrapping was fun as well.

Ha, the turbo side with the waste gates was tricky for sure.

WilliamFd55 · 05-03-2021, 12:48 PM

Picked up the last big ticket item of the build (Driveshaft). They did a hybrid setup, steel front/ aluminum rear. Got it installed and while I was under there, reworked the fuel delivery lines. Got rid of that weird loop.

SCOTI · 05-03-2021, 01:45 PM

Quote:

Originally Posted by WilliamFd55

Picked up the last big ticket item of the build (Driveshaft). They did a hybrid setup, steel front/ aluminum rear. Got it installed and while I was under there, reworked the fuel delivery lines. Got rid of that weird loop.

No way to remove those restrictive fittings? I've read where those hard/fabbed 90° fittings are the equivalent of adding >10' of additional line per fitting.

WilliamFd55 · 05-03-2021, 02:42 PM

Quote:

Originally Posted by SCOTI

No way to remove those restrictive fittings? I've read where those hard/fabbed 90° fittings are the equivalent of adding >10' of additional line per fitting.

I couldn't figure out a way to get the shut off fitting and first filter before the pump while keeping everything low, without all the crazy loops.

WilliamFd55 · 05-18-2021, 09:38 AM

Been working on a way to get inner fenders in while keeping it semi stock looking. Going to be a lot of cutting/ metalwork around turbo and back by the firewall, but this is where I have the most fun. So lets cut up some new fenders! Lap welds is where its at with this thin metal. Ended up raising the mounts about 2-1/2".

04-29-2021, 09:41 AM	#1
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,149	Re: His name is "George" 84' C10 Looks 'complicatingly' good. I bet wrapping was fun as well. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

05-03-2021, 12:48 PM	#3
WilliamFd55 Registered User Join Date: Dec 2016 Location: Glen Rock, NJ Posts: 258	Re: His name is "George" 84' C10 Picked up the last big ticket item of the build (Driveshaft). They did a hybrid setup, steel front/ aluminum rear. Got it installed and while I was under there, reworked the fuel delivery lines. Got rid of that weird loop. Attached Images

05-18-2021, 09:38 AM	#6
WilliamFd55 Registered User Join Date: Dec 2016 Location: Glen Rock, NJ Posts: 258	Re: His name is "George" 84' C10 Been working on a way to get inner fenders in while keeping it semi stock looking. Going to be a lot of cutting/ metalwork around turbo and back by the firewall, but this is where I have the most fun. So lets cut up some new fenders! Lap welds is where its at with this thin metal. Ended up raising the mounts about 2-1/2". Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.