47-55.1 Wiper motor and arms - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Nima · 10-03-2022, 10:20 AM

Hello:

Besides the wiper arms, are these 3 the only parts or am I missing a smaller arm? I am trying to convert to a newport engineering 12 volt motor and It has been a while since I have taken these pieces apart.
Thannks

leegreen · 10-03-2022, 01:37 PM

#3 is the passenger side linkage, you are missing the drivers side.

https://www.classicindustries.com/sh...-1535062464283

#2 is the oem vacuum wiper motor. Hard to see but I think you are missing the spring that keeps the linkage on
https://www.classicindustries.com/sh...w-811580860707

There is a knob on the dash with short linage to control motor

#1 looks like a single speed electric wiper motor from a rear wiper, boat or something

**mr48chev** · 10-03-2022, 03:41 PM

#1 is as Leegreen said a single speed electric wiper motor. Very commonly used on older flat fender jeeps and they were used on hot rods in the 70's quite a bit. My experiene says they don't work well on AD trucks although there were guys advocating using them in the 70's.

https://www.summitracing.com/parts/u...0aAlR8EALw_wcB

https://www.ebay.com/itm/13379772843...4aAnGwEALw_wcB

I've got one of those motors in a box somewhere if I didn't sell it at a swap meet.

Nima · 10-03-2022, 08:38 PM

Thank you guys.
Well, all these came out from udner the dash of my 53 GMC. I had them in a palstic bag during dissamebly but due to the lenght of the longer arm the plastic bag was not sealed well. So, I am assuming at one point the previous owner, decades ago, just installed the single stage motor on the drive side since I can't find the smaller arm. That is a bad news for me since the repalcement arms are spendy!

**mr48chev** · 10-04-2022, 01:00 AM

I've got an extra or two.

I've got a pair sitting somewhere that I pulled for some guy on FB who never got back to me if I can figure out where I put them or I can pull the left one off the orange cab easy enough. I'm not going to use that cowl at all if my plans hold true as I bought the truck to get the back half of the cab.

The big cost will be postage. Let me find the other one or get the one off the orange cab in the morning and find a box and weight it.

Nima · 10-04-2022, 09:46 AM

Quote:

Originally Posted by mr48chev

I've got an extra or two.

I've got a pair sitting somewhere that I pulled for some guy on FB who never got back to me if I can figure out where I put them or I can pull the left one off the orange cab easy enough. I'm not going to use that cowl at all if my plans hold true as I bought the truck to get the back half of the cab.

The big cost will be postage. Let me find the other one or get the one off the orange cab in the morning and find a box and weight it.

Thank you.

**mr48chev** · 10-04-2022, 10:25 PM

It ended up being haul my wife around day and I didn't get out to pull the arm off until later.

it looks like someone stripped the nut on that one along breaking the bezel.

My helper wasn't very impressed either so we will have to dig the other one out now.

At least we got a good sunset shot out of the deal and now I have to figure out what I did with the other one.

My wife's haircut came out good and lunch was good though.

Nima · 10-05-2022, 09:43 AM

Quote:

Originally Posted by mr48chev

It ended up being haul my wife around day and I didn't get out to pull the arm off until later.

it looks like someone stripped the nut on that one along breaking the bezel.

My helper wasn't very impressed either so we will have to dig the other one out now.

At least we got a good sunset shot out of the deal and now I have to figure out what I did with the other one.

My wife's haircut came out good and lunch was good though.

The kitty and the sunset are beautiful, the wiper arm with stripped tip is another story!

**mr48chev** · 10-05-2022, 04:46 PM

I only bought that truck for the roof and the back panel of the cab.

The roof and back side of the cab are near perfect but the rest of the truck had had a hard li

fe. It had about 500 lbs of brackets welded to the frame for pumps and a water

**mr48chev** · 10-07-2022, 01:57 AM

I finally found where I had stuck it.

20,00 shipped is what I need.

PM me for the details.

The bezel is a patina bezel that may or may not polish up and the nut has some marks on it

10-03-2022, 08:38 PM	#4
Nima Blue 67 Join Date: Apr 2004 Location: Western WA Posts: 1,179	Re: Wiper motor and arms Thank you guys. Well, all these came out from udner the dash of my 53 GMC. I had them in a palstic bag during dissamebly but due to the lenght of the longer arm the plastic bag was not sealed well. So, I am assuming at one point the previous owner, decades ago, just installed the single stage motor on the drive side since I can't find the smaller arm. That is a bad news for me since the repalcement arms are spendy! __________________ 1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner

10-04-2022, 01:00 AM	#5
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,715	Re: Wiper motor and arms I've got an extra or two. I've got a pair sitting somewhere that I pulled for some guy on FB who never got back to me if I can figure out where I put them or I can pull the left one off the orange cab easy enough. I'm not going to use that cowl at all if my plans hold true as I bought the truck to get the back half of the cab. The big cost will be postage. Let me find the other one or get the one off the orange cab in the morning and find a box and weight it. Attached Images __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

10-04-2022, 10:25 PM	#7
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,715	Re: Wiper motor and arms It ended up being haul my wife around day and I didn't get out to pull the arm off until later. it looks like someone stripped the nut on that one along breaking the bezel. My helper wasn't very impressed either so we will have to dig the other one out now. At least we got a good sunset shot out of the deal and now I have to figure out what I did with the other one. My wife's haircut came out good and lunch was good though. Attached Images __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

10-05-2022, 04:46 PM	#9
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,715	Re: Wiper motor and arms I only bought that truck for the roof and the back panel of the cab. The roof and back side of the cab are near perfect but the rest of the truck had had a hard life. It had about 500 lbs of brackets welded to the frame for pumps and a water __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

10-07-2022, 01:57 AM	#10
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,715	Re: Wiper motor and arms I finally found where I had stuck it. 20,00 shipped is what I need. PM me for the details. The bezel is a patina bezel that may or may not polish up and the nut has some marks on it Attached Images __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

10-03-2022, 10:20 AM	#1
Nima Blue 67 Join Date: Apr 2004 Location: Western WA Posts: 1,179	Wiper motor and arms Hello: Besides the wiper arms, are these 3 the only parts or am I missing a smaller arm? I am trying to convert to a newport engineering 12 volt motor and It has been a while since I have taken these pieces apart. Thannks Attached Images __________________ 1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner

10-03-2022, 01:37 PM	#2
leegreen Registered User Join Date: Mar 2022 Location: Surrey BC Posts: 917	Re: Wiper motor and arms #3 is the passenger side linkage, you are missing the drivers side. https://www.classicindustries.com/sh...-1535062464283 #2 is the oem vacuum wiper motor. Hard to see but I think you are missing the spring that keeps the linkage on https://www.classicindustries.com/sh...w-811580860707 There is a knob on the dash with short linage to control motor #1 looks like a single speed electric wiper motor from a rear wiper, boat or something

10-03-2022, 03:41 PM	#3
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,715	Re: Wiper motor and arms #1 is as Leegreen said a single speed electric wiper motor. Very commonly used on older flat fender jeeps and they were used on hot rods in the 70's quite a bit. My experiene says they don't work well on AD trucks although there were guys advocating using them in the 70's. https://www.summitracing.com/parts/u...0aAlR8EALw_wcB https://www.ebay.com/itm/13379772843...4aAnGwEALw_wcB I've got one of those motors in a box somewhere if I didn't sell it at a swap meet. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.