Shawno72's long overdue 68 daily driver build thread

[shawno72]

Originally Posted by Ol Blue K20

Sorry Shawn, the corvette thing got past me but as long as the booster is working it sounds like line pressure problem. The corvette was usually 4 piston calipers on all four corners. Do ya know someone you can borrow a stock truck master w/ discs/drum combo to try out. I'm just wondering if the vette had different pressure requirements

I was thinking that the Corvette master would be overkill if anything. Should squeeze those calipers with no problem. I'm thinking that maybe the booster is the issue. I noticed on the O'Reilly website that the corvette booster is a dual diaphragm.

[Ol Blue K20]

Originally Posted by shawno72

I was thinking that the Corvette master would be overkill if anything. Should squeeze those calipers with no problem. I'm thinking that maybe the booster is the issue. I noticed on the O'Reilly website that the corvette booster is a dual diaphragm.

good thought, did you change the booster as well. I see the new prop valve

[BB72CHEVKT]

Looks good!

[shawno72]

Originally Posted by BB72CHEVKT

Looks good!

Thanks man!!

[jlsanborn]

Truck is looking sharp man, nice work! So them spindles are a 2-1/2" drop, plus a 3" spring??? What size rubber on there?

[shawno72]

Originally Posted by Ol Blue K20

I would think the stock booster would work with the vette master but now I'm not sure. I'm sure the booster is still working or you would hear the vacuum under the dash when brakes are applied or run funny. Only I can think of is the master isn't making the pressure you need. You're getting good pressure when bleeding correct?

Actually the pressure is ok but not super great. Not bad enough to cause concern.

Originally Posted by jlsanborn

Truck is looking sharp man, nice work! So them spindles are a 2-1/2" drop, plus a 3" spring??? What size rubber on there?

Thank you!! Yes 2.5" spindles and 3" springs. Tires are P215/70R15 up front and P235/75R15 out back.

[Ol Blue K20]

Originally Posted by shawno72

Actually the pressure is ok but not super great. Not bad enough to cause concern.



Thank you!! Yes 2.5" spindles and 3" springs. Tires are P215/70R15 up front and P235/75R15 out back.

Well Shawn, I'm at a loss, the only thing I can think of is the master. Trucks run one large piston and vettes four small pistons. I would try a truck power master and see how that changes things.

[shawno72]

Originally Posted by Ol Blue K20

Well Shawn, I'm at a loss, the only thing I can think of is the master. Trucks run one large piston and vettes four small pistons. I would try a truck power master and see how that changes things.

The booster is working good so either I need a different master or a bigger booster........I think
Posted via Mobile Device

[jlsanborn]

Originally Posted by shawno72

Actually the pressure is ok but not super great. Not bad enough to cause concern.



Thank you!! Yes 2.5" spindles and 3" springs. Tires are P215/70R15 up front and P235/75R15 out back.

Thanks! If you get a chance, snap a picture of the ground clearance at the a-arms. I'm banking on a 4-1/2" advertised drop (2-1/2 + 2) and 235/60's working for me.

[shawno72]

Originally Posted by jlsanborn

Thanks! If you get a chance, snap a picture of the ground clearance at the a-arms. I'm banking on a 4-1/2" advertised drop (2-1/2 + 2) and 235/60's working for me.

Your welcome. I'll snap a couple pics tomorrow.
Posted via Mobile Device

[shawno72]

Originally Posted by jlsanborn

Thanks! If you get a chance, snap a picture of the ground clearance at the a-arms. I'm banking on a 4-1/2" advertised drop (2-1/2 + 2) and 235/60's working for me.

Well it's not a very good pic but I hope it helps. I would say the LCA's are about 2.5" off the ground.

[shawno72]

Look what I got today. Do you know what this means?

[jlsanborn]

Originally Posted by shawno72

Well it's not a very good pic but I hope it helps. I would say the LCA's are about 2.5" off the ground.

Attachment 1086175

Yikes! I'd theoretically be 1/2" or so higher but that's probably pretty nominal. It's going to be low and I sure can't say the same about our streets up here. Thanks for photo man!

[fastcam1]

Install tonight!
Posted via Mobile Device

[shawno72]

Originally Posted by fastcam1

Install tonight!
Posted via Mobile Device

Very soon, very soon.

[sduckworth13]

Hey Shawn, your truck is looking great. Nice job on the suspension, how does it ride now? I did a similar setup and my 1967 GMC longbed truck, rode like it was on rails going around corners.
Posted via Mobile Device

[shawno72]

Originally Posted by sduckworth13

Hey Shawn, your truck is looking great. Nice job on the suspension, how does it ride now? I did a similar setup and my 1967 GMC longbed truck, rode like it was on rails going around corners.
Posted via Mobile Device

Thanks Scott. The truck rides so much better with the correct lowering springs. Not quite on rails but much stiffer through the turns

I will probably install the rear air bags this weekend

[sduckworth13]

Lol, I guess any upgrade of suspension I would say was like riding on rails when I did my suspension. I had the death wooble going on, you know when you only was going change one lane and your truck decides it wants to change two and the only way to make it quit wobbling was to drive faster... Lol. Nice work, looks great.
Posted via Mobile Device

[Daaaanz67]

Phew that's low, I know Lodi has good roads what about some of those long trips that you'll be going on and what you might encounter. I'd like to go lower on mine but to worried. Roads in my area are pretty rough. Anyways looking good Shawn.
Posted via Mobile Device

[shawno72]

Originally Posted by Daaaanz67

Phew that's low, I know Lodi has good roads what about some of those long trips that you'll be going on and what you might encounter. I'd like to go lower on mine but to worried. Roads in my area are pretty rough. Anyways looking good Shawn.
Posted via Mobile Device

Thanks Dan, yeah up there where you are I can see some of the roads getting a bit rough. For me its the price I'm willing to pay to look

[C10_ustacould]

And it does look!

[Hardesty454]

You can come try on my 20's... They're 6 lug!
Posted via Mobile Device

[shawno72]

Originally Posted by Hardesty454

You can come try on my 20's... They're 6 lug!
Posted via Mobile Device

With the disc brake install and new rest axles I'm 5 lug now. Got any 5 luggers?
Posted via Mobile Device

[Hardesty454]

Originally Posted by shawno72

With the disc brake install and new rest axles I'm 5 lug now. Got any 5 luggers?
Posted via Mobile Device

Not here, I'm going to be swapping over to 5 lug eventually. Not yet though.
Posted via Mobile Device

[HotRod C/10]

Originally Posted by shawno72

With the disc brake install and new rest axles I'm 5 lug now. Got any 5 luggers?
Posted via Mobile Device

I do, and you can get some real Mexican food while your here!