? on parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cduster · 01-02-2003, 08:11 PM

Hi all,
New to the boards, but thought I might ask where is the best place to buy OEM parts? I am restoring a '72 GMC 1/2 ton stepside. I am needing a core support, and fenders. I thought OEM for a better fit, as I have had some trouble fitting parts b4.

Any insights as to OEM or aftermarket would be appreciated. Thanks

JimKshortstep4x4 · 01-02-2003, 09:09 PM

Welcome to the board from West Michigan!

Since you have a GMC, I would suggest that you contact GMC Paul.

His site his: www.gmcpauls.com

He carries a good line of parts,(unsure on oem saddle) and he is very knowledgeable on GMC's

Jim

cduster · 01-02-2003, 11:19 PM

Hi Jim, Kentwood- not too far from me. I'm in South Haven. Thanks for the tip. Dan

RACING29 · 01-03-2003, 12:17 AM

CLASSIC INDUSTRIES

JimKshortstep4x4 · 01-03-2003, 09:40 PM

Dan,

Good luck on your GMC stepside. That should make you a nice truck.

I just finished up a 71 Chevy short step 4x4 this fall and it is a
blast to drive. The steps are not too usefull for hauling though.
Luckily we have other trucks, (9) total.

Caution! This site is addictive!

Jim

**Tim Christian** · 01-03-2003, 09:59 PM

A Big Tennessee Howdy-Do!!!!

01-02-2003, 08:11 PM	#1
cduster Registered User Join Date: Oct 2002 Location: S.W. Michigan Posts: 403	? on parts Hi all, New to the boards, but thought I might ask where is the best place to buy OEM parts? I am restoring a '72 GMC 1/2 ton stepside. I am needing a core support, and fenders. I thought OEM for a better fit, as I have had some trouble fitting parts b4. Any insights as to OEM or aftermarket would be appreciated. Thanks

01-03-2003, 12:17 AM	#4
RACING29 Registered User Join Date: Jul 2002 Location: Tennessee, Morristown Posts: 355	CLASSIC INDUSTRIES __________________ 1967 Chevy truck, R1 racing seats, 4 point racing harness, 4/6 drop, primered blue, soon to be shaved, 350- 060. over, flat top pistons, Eagle rods, Edelbrock Aluminum heads, 1.5 Scorpion roller rockers, Lunati 515" cam, mallory ignition, Holley 750 double pumper carb, Built 350 turbo trans, 2500-2800 boss hog stall, 20 gallon aluminum fuel cell!!!

01-02-2003, 09:09 PM	#2
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Welcome to the board from West Michigan! Since you have a GMC, I would suggest that you contact GMC Paul. His site his: www.gmcpauls.com He carries a good line of parts,(unsure on oem saddle) and he is very knowledgeable on GMC's Jim

01-02-2003, 11:19 PM	#3
cduster Registered User Join Date: Oct 2002 Location: S.W. Michigan Posts: 403	Hi Jim, Kentwood- not too far from me. I'm in South Haven. Thanks for the tip. Dan

01-03-2003, 09:40 PM	#5
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Dan, Good luck on your GMC stepside. That should make you a nice truck. I just finished up a 71 Chevy short step 4x4 this fall and it is a blast to drive. The steps are not too usefull for hauling though. Luckily we have other trucks, (9) total. Caution! This site is addictive! Jim

01-03-2003, 09:59 PM	#6
Tim Christian Senior Member Join Date: Dec 1999 Location: TN/VA Posts: 6,388	A Big Tennessee Howdy-Do!!!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.